GTH18DBXARCC General Electric Refrigerator - Instructions

2 screws. how easy can i get.

Take out both vegetable drawers. Lift back of shelf first then front until you hear the click from both front sides. The shelf should now be loose and you can take fully out. Remove the glass shelf from the plastic frame by turning the shelf over and pulling back and up from the rear part of the glass. Put the glass into the new plastic frame by doing the same technique. Then put the shelf back into the fridge by the resting the shelf down in the correct position and pushing the front of the shelf until you hear the click again on each side. slide the drawers back into place and you are done!

I came home to find a mess near the refridgetor. My teenage daughter or son had made themselves a peterbutter and strawberry homemade jam sandwhich. The strawberry jam was all over the inside of the door and on the floor. What a mess, so I was waiting for my husband to change the gasket around the door anyways. So I though to myself I just change it myself. The old one just came off and I pulled the new one out of the box and I went right on with not much effort. ( I wiped down the area after I put off the old gasket) Thank you very much for making the parts so easily avaiable on your website without having to buy a new refrigator. Thanks again Sue and Ed

Turn off refrigerator. Remove the plastic air flow cover, styrofoam channel and metal panel inside freezer compartment, remove hex nuts holding motor mount, unplug connector, remove old grommets, remove compression ring, (note 1/4 inch extension of shaft through fan) carefully pull fan blade off motor shaft and put on new motor shaft, leaving 1/4 inch of shaft extending through, replace compression ring. If your new fan motor has a female snap connector and the old motor has a male connector (as mine did) you will have to cut the wires on both new and old motors, splice and solder the male connector onto the wires of new motor, wrap carefully with premium electrical tape (or shrink tubing). Replace the 2 grommets, Reconnect the fan and bolt back into place. Make sure all the bolts around the mount are tight. Replace the metal panel. Manually spin the fan making sure it is free of the shroud. If it binds in the shroud, physically move the motor and mount till it rotates freely. Turn on refrigerator and test fan operation. If it's all good, replace the styrofoam and plastic cover.

took the old stop off put the new stop on

replace the bar lift top off

Because the kit did not include fasteners, had to use wood screws and superglue.

Replaced above parts and the noise problem was not resolved. Ordered a new motor, fan blade and another set of grommets from PartSelect. The parts were delivered the next day. Took me about 15 minutes to swap the new parts in. It's been 3 days since the repair and the noise has not returned.

Just unscrewed old handles & screwed in the new one. Very easy. Have a good Phillips head screw driver.

per your instructions

I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.

Connected the 2 wires and pushed in the switch until it clicked.

The repair is very simple, the gasket sits in a channel in the door. Just start with a corner and pull the old gasket out. Once you've removed the old gasket, push the new gasket into the same channel. Make sure you've completely pushed in the new gasket all the way around the door. It's as simple as that. The repair takes less than 5 minutes per door.

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy

Only took a screwdriver to take two screws out & install new slide with the two existing screws. Very easy. Took less than 5 minutes. Great website I found on Google right away, just by searching for refridgerator parts. After ordering part, only took a few days to come in.