GTS16BCSDRCC General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Harrisburg, PA
- Parts Used:
- WR32X10398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old cover was cracked and needed replaced
The repair only required removing nthe old cover and installing the new one. What I was really surprised about is the time for delevery. I ordered the part on Friday morning around 11 AM and it was delevered by Fed Ex at 8:30 AM on Saturday morning. I am not sure how many locations they have, but this must have been close to Harrisburg, Pa.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sophie from WASHINGTON, DC
- Parts Used:
- WR17X11890
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken freezee door shelf
Click shelf into place!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from TEXARKANA, AR
- Parts Used:
- WR17X11890, WR17X11889
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I never had Door shelving
Just popped them in their slots. Very easy and it made my refrigerator brand new again.. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bradley from Cedarburg, WI
- Parts Used:
- WR60X10207, WR02X12149
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Condensor fan blade cracked, blade was sheared off.
First, remove the cardboard cover on the back, lower portion of the refrigerator.
Next, locate the condensor fan motor assembly and blade. (Right side as you are facing)
Using a pliers, hold the shaft to keep it from turning and prevent damage to the motor. Using a screwdriver, slide the old ring compression on the blade shaft toward the motor (away from the fan blades) to loosen.
Remove old blade from the shaft by firmly grasping the motor shaft with a pliers (to prevent from damaging) and pull the blade assembly off.
Reverse the above steps to attach the new blade.
Next, locate the condensor fan motor assembly and blade. (Right side as you are facing)
Using a pliers, hold the shaft to keep it from turning and prevent damage to the motor. Using a screwdriver, slide the old ring compression on the blade shaft toward the motor (away from the fan blades) to loosen.
Remove old blade from the shaft by firmly grasping the motor shaft with a pliers (to prevent from damaging) and pull the blade assembly off.
Reverse the above steps to attach the new blade.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from HAYDEN, CO
- Parts Used:
- WR32X10398, WR71X10378
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Crisper Drawer Cover was broken, and i wanted to add a third shelf for my garage fridge
I slid the old crisper drawer cover out, and slid the new one in. Then I respaced the other shelves, making room for the third shelf, and put the new shelf in. Apart from the time it took me to unpack the boxes these parts came in, and to remove my groceries from the fridge, the "repair" itself took all of about 90 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose A from WEST PALM BCH, FL
- Parts Used:
- WR09X20002
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Was getting too cold
Was only two screws after that carefully took the part away unplugging the wires at the same time was plugging in to the new part and was done after 5 or 7 min
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from TUCKER, GA
- Parts Used:
- WR17X11890
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing shelf
Went right on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from Minneapolis, MN
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ice maker was leaking
thats what I did is remove the teo screws and took the old single outlet valve out. And put the new one in and put the screws back in. First turned off the water and put the water back on after I was threw and no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Riverdale, NJ
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Water leaking and freezing everywhere. Weird shaped ice cubes, more like chunks which jambed the dispenser.
First removed the two screws that holds the old ice maker in place. Unplugged it. The freezer compartment was too narrow to allow the unit to slide out or turn in any other direction. Had to also remove the two front screws from the left side ice bin track and swing it down. The door opening was also too tight. Scratched the plastic door jamb putting the new unit in but other than that all is well and functioning well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eli from Buford, GA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker
Remove ice maker out of fridge; remove 3 screws
replace defective part re-install all components 30 minutes later " magic ice again. Very easy repair most important low cost. Thanks "Parts Select"
replace defective part re-install all components 30 minutes later " magic ice again. Very easy repair most important low cost. Thanks "Parts Select"
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from WESTON, CT
- Parts Used:
- WR30X10093
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker stopped working
Installation could not have been easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- timothy from aberdeen, MD
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
water not being drawn up into icemaker
unplugged the old valve and disconnected the water line, then reconnected water line on new valve and plugged it in. It was an easy process but unfortunately that did not fix the problem. It is the ice maker it self so I will be ordering a replacement ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from ORO VALLEY, AZ
- Parts Used:
- WR57X10033
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Water leaking from bottom of refrigerator
I'm not a DIY-er, and wasn't sure a 20 year old refrigerator was worth the repair, but for $30 I could afford to be wrong. The swap is pretty intuitive, especially in my case since the problem was that the water tube from the valve to the ice maker had detached from the coupling. So I didn't have to cut anything off, just inserted the tube into the new valve. Reconnected the supply line, screwed the assembly back on the refer, and Bob's your uncle. Other than unloading some canned goods to lighten the refer, longest process was finding the right size nut driver in my disorganized tool tray. Be aware, there are NO instructions included with the part. Found a good video on you tube that confirmed the obvious. Glad I took a shot!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from UNION CITY, NJ
- Parts Used:
- WR17X11889
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fixed shelf was cracked.
I popped out the old plastic shelf and slid in the new one. It was self explanatory and took less than one minute with no tools.
Was this instruction helpful to you?
Thank you for voting!