GTE22FBTJRWW General Electric Refrigerator - Instructions

Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.

Removed shelves and light bulb. Undid the two screws on the back panel with nut driver. Snipped the two wire leads to the defrost thermostat. ( orange and pink wires) Carefully removed the defrost thermostat from the coil. Stripped both ends of the wire leads about a half inch and onnected with two wire nuts. Then wrapped with electrical tape to seal from moisture. Carefully attached defrost thermostat to coil. Screwed the back panel back on. Reinstalled light bulb and shelves. And plugged refrigerator back in. Works like a charm. Saved close to 100.00 dollars doing repair myself.

Defrost cycle staying on too long causing ice to melt, refreeze and seizing up ice maker. Replaced temp sensor and defrost thermostat just to be sure. Fixed the problem.

It was very tricky getting the old piece out, even though it was partially broken... I ended up snapping the old piece to remove it. Trying to install the new track with the glass shelf above was not working at all, but once I removed the glass shelf above it, the new piece went in pretty easily. With the glass shelf out, I could angle the track upward to get it into position. In retrospect, I should have removed the glass shelf from the start... it would have made removal of the old piece much easier.

Only problem we had was when we removed back wall on freezer the couls were totally iced up. After waiting for that to defrost. (3 HOURS) repair went fine. Was kind of hard to get to the part being its a side by side but happy with results

I followed the directions of the how-to video and completed job in less than 15 minutes and it solved the problem. It's been freezing like before.

My snack tray guide rail cracked and this was the easiest repair I've ever made.

I have checked the defrost thermostat:During the defrosting cycle the thermostat is still open

replaced the defrost thermostat. The "how to" video was superb. Watched it twice before beginning the job. repair went as described.

Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold

I looked at the video that came with the part and followed what i saw. My wife and i was about to go out and spend between $1500 and $2500 on a new refrigerator due to continuous defrosting. It had been happening for about a year. I followed the instructions from the video and the defrosting has stopped. Thanks so much for the video and the part! We do not need a new refrigerator after all.

I called a repair shop and they said the control bd. was bad. They replaced it and about 2 weeks later it happened again. They came out again and replaced the bd. under warranty. About a week later it happened again. This seemed like too much of a coincidence, so I looked around on the internet and found your site. The video showed how to replace the freezer safety thermostat which I ordered on Sunday and received on Tuesday. By then the coils were iced up again. I completed the repair in about half an hour. So far the old GE is working like new. Thanks for the help. I just wish I hadn't spent over $400 for incompetent repair people in the first place. Thanks again, you guys are great! By the way the part only cost about $17 including shipping.

I went on Parts Select and typed in the problem, and they gave me the parts that might be the problem. So, I ordered the two parts, and put them in. Was really easy, as there are videos on parts select to help you remove the part and put the new one in. So simple. My freezer is working right now, so time will tell.

I watched the video then ordered the defrost timer it was here in two days (ordered late saturday arrived tuesday). Spent $. 16 On two wire nuts and went to work . The repair took one hour including defrosting the coils with a hair dryer . Your website is my " go too " for parts and repair. I spent less than $20 including shipping !

I looked at your video . very nice. job went fast. thank you mike.