GSS20IETPWW General Electric Refrigerator - Instructions

I followed the isntructions of another fellow who had repaired his ice maker, but made the mistake of taking the ice crushers apart before noting where the fixed blades were to be reassembled. Since there was not a schematic with the part I had to go on line to your site and enlarge and use the one there, while accurate, was very hard to read and when I finished, I think it is in the wrong place as I'm not able to get the fineness of crushed ice I had before the repair, but absent a very legible schematic I'm not going to try to fix it further. The auger works, gives us ice cubes and half crushed cubes.
Another tip for future repairers is to to wait for the ice container to warm up or use a hair drier on the part where the tabs need to be depressed to slip off the blade housing. When cold it's extremely brittle, but since I had to leave the job for later at one point and left in on my work bench I found it much more pliable and easy to assemble.
All in all, I'm OK with the part and the result, but wish I could have gotten the fixed blade back into the right spot.

Removed the plastic frame by pushing to the inside (all 4 sides), removed touch pad by sliding it to my right and disconnected the wires. Removed the four screws that hold the dispensing unit and replaced broken parts. Please note that I also replaced the funnel. Total cost of repair for DIY $30.00, savings by avoiding repair man, priceless.

Removed tray, threw out ice , removed 3 screws used 2 screw drivers to seperate part & re installed

1) Unplug Refrigerator. Remove all shelves and light shield in the freezer.
2)Remove panel covering refrigeration coils inside freezer in back. Two hex head screws w/nut driver.
3)Remove the defrost heater using phillips screw driver. Two screws.
4)Unplug two quick disconnect stakons and wires from heater.
5)Plug the wire coming down the right side into one side of the new heater and plug the shipped white wire into the other quick disconnect spade at the heater.
6)Install the new dual element defrost heater into the same place where the old was. Connections to the right.
7)Route the wire that was on the left across the top of the coils and down the right side.
8)Bring the existing wire from the left side down the right side and the white wire up the right side. Wires should not be tight at all and do not remove the tape at the stakon.
9)Now wires need to be cut (if necessary)and crimped together in the shipped stakon. This stakon looks like a wire nut.
10)Wires should be tucked gently into the styrofoam up and down the right side. Wirenut should be positioned so that water can not collect in it.
11)Replace the panel over the cooling coils.
12)Plug Refigerator back into the wall outlet. Put shelves and light shield back in.
13)My refrigerator is now working without a problem. It's been est two weeks.
Ice maker is also working correctly.

Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!

First I removed ice bucket and emptied. I then removed screws that held the covers in place. Next I removed the snapring that held the auger in the covers and removed auger assembly. Replaced both covers and reassembled.

You must have a nutdriver to replace this part. No wrench or pliers will fit in the space to loosen any of the nuts.

You cannot simply replace the bracket, because it's connected to the ice-maker assembly and it's a very snug fit. Therefore, you must remove the bracket on the opposite wall to give you room to angle the assembly and slip on the new bracket.

Be careful when you're screwing the nuts back in, especially the two in the back of the freezer. It's a difficult angle to keep a grip, and it's easy to drop the screws into the freezer (and then you have to fish them out of the bags of frozen peas)

1 - Remove the nuts from the broken bracket.

2 - Remove the nuts from the bracket on the opposite wall.

Now you have room to maneuver.

3 - Angle the ice-maker assembly and slip off the old bracket, and then slip on the new bracket.

4 - Align the brackets over the holes and screw in each nut.

The most difficult part was screwing in the two back screws when replacing the brackets onto the freezer walls. It's a pretty simple job that requires no muscle.

The hard part was cleaning the dust around the coil and fan area. Its plug and play right after that. Two nuts on the fan housing and a wire harness snaps on and off. Bam! 1,2,3 Up and running. . Like new. . . Thank you ps

I tried to quite the noisey evap motor with special liquid motor grease from Radio Shack. It did not work, so I ordered the evap motor. My freezer motor was wired slightly different than the motor I received. The replacement motor had a male plug attached to the four wires, the original motor was different, so I cut the wires and spliced them into the original freezer wires (colors were the same). Remounted motor. Works great, and no more groaning motor
Peter

Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.

1. Removed the back panel of the fridge to get access to the inlet water valve.
2. Removed black poly water line from valve (pull back on white ring where line is attached and pull the line out)
3. Removed the inlet tube from top-back of fridge (where it goes into the ice make). use putty knife to get under the sticky white gasket beneath the black oval housing and pull the tube out form the back of the fridge.
4. Replace the water line with new part taking care to properly seat the line into the the bottom water valve and pushing the water tube into the hole for the ice maker.

Note: Be sure to take off the protective covering from the white - sticky grommet and push to adhere to metal on fridge.

to be safe - use a bit of clear silicone chaulking round the perimeter of the grommet and push to tighly bond the water inlet tube to the fridge.

The reason for this - is that if you do not get a good bond using the white - sticky gormmet alone - you may have the water tube inside the ice maker freeze up.

Also once the new water line is installed be sure to secure the line to the metal back of the fridge - so the line will not move. some fridges come with metal hose clamps to do this - otherwise use duct tape

I am 80 years old, female. Repair was a challenge but I was determined as my son said Mom you can do it. The video was wonderful. and I did a lot of rewinding etc. Hardest part was taking apart.. screws tough. All in all not bad. I don't want to do it for a living though!!!!! Ice is now dispensing!!!!!!!!!!!!!!!

I bought a Flapper replacement part from Parts Select. I installed it following their very complete on-line video directions. Their complete and easy to follow directions made my job very easy, and the work was completed without any problems and just as good as if it were done by a professional repair person. I am proud of my work, it couldn't have been done without their video insructions. Also I got delivery of the part within two days of my order. I will alway look for Parts Select any time I need an applicance repaired. Thanks to Parts Select!

I removed the outer plate by sticking a very small screwdriver in the small holes at the bottom of the plate and pulling the plate toward me.
I then removed the 4 screws from the internal plate and pulled the plate toward me.
Then I romoved the 3 screws holding the old solenoid and unplugged it.
Next I put the new solenoid in place and replaced the three screws.
Finally I plugged in the solenoid and replaced the internal and external plates.

ice makes would not make ice. first i filled ice tray with water. the ice maker did make ice then, but did not refill with water. So replaced water inlet valve. workes great!!