GTE25DBTJRWW General Electric Refrigerator - Instructions

I called angies list to get a name of a repair person . We were having very hot weather and I did not want my freezer food to spoil. The cost was not bad for the look see $127.00 plus parts and labor added on to this. I decided to look on the internet and found your services and the video on how to replace the part that might be bad. I bought a new thermostat and also a sensor and added the control board as the refrigerator is 13 years old. I spent a total of $206.00 and did the work myself so no labor cost. I was so happy as a new refrigerator like this one would be $3100.00 plus tax. Thank You R. Polglase

I can't tell you how luck I feel after finding your website I ordered the temperature sensor after watching one of your videos on-line and the repair went just as on the video. I pulled the "bad" sensor out, and replaced it with the new one. Keep in mind that this is the first time I ever touch an appliance, needless to say I'm feeling pretty good about that! All in all it took me about 20 minutes to complete my repair and it now has been about 4 days and the refrigerator is working like new again!

1. Removed and tested defrost heater, tests good. 2. Reinstalled defrost heater. 3. Removed and tested defrost over-temperature sensor, tests good. 4. Reinstalled over-temperature sensor using soldering iron, dielectric silicone grease, and heat-shrink tubing. 5. Removed the control printed circuit board and checked for blown fuse's, fuse's are all good. 6. Removed the defrost relay from the printed circuit board using soldering iron, bench tested the relay, it is good. 7. Soldered defrost relay back onto the circuit board, and reinstalled control board. 8. Removed and bench tested evaporator thermistor, the resistance is out of specification, ordered new thermister. 9. Installed new thermistor using soldering iron, dielectric silicone grease, and heat-shrink tubing. 10. Re-assembled refrigerator. 11. Installed temperature monitoring and recording instrumentation for 72 hour test. The defrost cycle is running correctly with a defrost termination temperature of around 90 deg-f. The defrost cycle ran twice while running the 72 hour test. 11. Removed test instrumentation and Put the unit back into service, The thermistor was the culprit. I bought the right part on the first shot, nice.

Part select was great. I entered the model number and was able to locate a list of problems associated with my refrigerator. I was able to view a repair video, courtesy of part select. I followed the instructions and the repair was simple. The hard part was trying to remember how everything went back together. I unplugged the unit and removed the freezer racks. I then unscrewed the back panel within the unit. I then placed an old towel inside the unit and used a hair dryer to melt the ice build up inside. I also removed the light bulb and then removed ice maker. I then located the old defrost thermostat and replaced it as demonstrated in the video. I then located temp sensor and replaced it. It took longer trying to secure the rear panels than the actual repair. My mistake was I had secured the ice maker unit before securing the fan panel. I would secure the large panel first, then followed by the light bulb/fan panel. The ice maker should go in last. It has been 8 days since the repair and it still working! The total cost was $27.

removed evaporator coil cover inside freezer, defrosted the coil with blow dryer, cut wires to defrost thermostat, removed old defrost thermostat, wired new one to old wires with wire nuts and then taped with black electrical tape, reattached defrost thremostat to evaporator coil, easy job, the thing that took the longest was thawing out all the ice

Replaced the Defrost Thermostat and the Defrost Heater.

Very limited working space in this model. Must remove grill and disconnect elect connector on motor. One additiional tool suggested: Extendable rod with magnet on end because you will most likely drop something. First, remove two screws holding motor to metal strap. Tool must be inserted between blades of fan in order to get to the screws and this is the hard part. Fan and motor are removed as one assy and this takes some manuvering. Might have to remove front screw on metal strap to gain more room. I did not attempt to remove fan shroud. My fan was attached to the motor shaft with a metal clip. Spray a good lubricant such as PB Blaster on the shaft, wait a few minutes and press it or tap it out gently. Save misc parts on old motor for reassembly. Your set up may be different so check out everything before starting.

first unplug unit then pulled the inside back freezer cover off piled towels around and defrosted the the unit thoroughly. located the defroster unit tested for continuity was good so i replaced the temp sensors they were just nip off the old one and splice in the new one. also replace the defroster thermostat was the same nip and splice. *the parts shop did not find the model #i have but knowing those parts are interchangeable with all G-E models i ordered the parts

Had to remove all the covers and fans to expose the condenser, which was difficult as the parts were frozen to it. The styrofoam covering the condenser made it almost impossible to defrost it. Therefore, I ripped the styrofoam off to expose the condenser. Was not really difficult to fix the styrofoam cover using metal tape. Replaced temperature sensor in aluminum block, and used butyl sealant to secure. Had to also re-install parts of ice-ball kit that were not well covered. Lots of parts to keep track of, but anyone could do it.

After replacing the Defrost Thermostat, Defrost Heater Assembly, and the Main Board, I concluded that the problem must be the Defrost Thermistor, which I replaced in less than 10 minutes and it fixed the problem! I cut the wires on the old thermistor and connected the new one after stripping the wires and taped the new connections with electrical wire. Fast and easy repair (the last part anyway ;).

I ordered 3 temperature Sensors Part#PS304103 and viewed the video. Got there, opened the frig. and it looked totally different and no place in any part of this frig. that took these sensors as viewed on the video. Totally baffled why these parts were listed for this frig. there was no place in this frig that would access for these parts. Serial # was HR443071.Maybe this model is out of date for these parts. Trying to find someone who can repair it. Any ideas???Purchased this GE in 2008. Model #is GSS25WSTFSS Thanks, for your help. JIM

Open up the freezer make shore the fan is running/unplug the unit take out the Shelf,s take a 1/4 inch nut driver and take the back panel out pull out the ice box pull up on the back panel and pull it out to expose the coil it should be blocked with ice if it is take a blow dryer and defrost it unplug the fan and push it up. On top of the coil you will fiend the defrost timer take your hand and unstrap it and pull it out. Cut the wires and strip the wires back enough take the new part and wire nut the wires together and tape with electrical tape and put back on the coil. Put every thing back together your dun plug the unit in and wait over night if you can to let every thing cool.

I followed the video instructions. It looked easy to do and it was. the video gave helpful little thing about the repair that made it easy. And it worked

followed part select video instructions

Replace defrost termostat and temperature sensor