GTE25DBTJRWW General Electric Refrigerator - Instructions

Defrost cycle staying on too long causing ice to melt, refreeze and seizing up ice maker. Replaced temp sensor and defrost thermostat just to be sure. Fixed the problem.

removed back panel from freezer. located thermostat removed and replaced thermostat put panel and all baskets back into freezer and plugged fridge back in. Works perfect problem solved

I followed the directions of the how-to video and completed job in less than 15 minutes and it solved the problem. It's been freezing like before.

Pried the corners off and replaced

Change thermostat and temperature sensor in the freezer section, but did not resolved the problem. Ordered the Main Control Board. After replaced the Main Controller Board. Refrigerator is back to normal.

fallowed the short video and it was as easy as changing a light bulb

Temp. Sensor was under an egg shaped cover on the left side wall in the refrigerator. Remove the cover, cut the two wires to the old sensor and remove it. Connect the new sensor to the two wires using butt connectors. Replace cover and done.

My son replaced both temperature sensors and the fridge works great now!!! Like brand new again!!!!

Only problem we had was when we removed back wall on freezer the couls were totally iced up. After waiting for that to defrost. (3 HOURS) repair went fine. Was kind of hard to get to the part being its a side by side but happy with results

I was intimidated by this repair(as I am with most repairs), because there were 2 possible problems. But being able to purchase both parts for $30 (including shipping) made it worth a try. Thanks to the instructional videos that were sent, the repair was much easier than I anticipated. For me, the hardest part was fitting my shoulders in the narrow freezer. Now the appliance works like a charm. This would have been a $150-$200 repair had I called a company to do it.

I identified the noise was coming from the coils / and the fan. Cleaning the fan helped reduce the noise a bit but it still kept recurring. I ordered the part, which was really easy using the diagram on the website. The instructions and the video were really helpful and was able to remove the old motor and replace it with the new one with relative ease. While there I cleaned the fan blade and vacuumed the surrounding area. This whole repair went quite smoothly and has given me the confidence to take on other repairs before calling out the repairman.

no brainer,watched the video,worst thing was to thaw the freezer,it was realy frosted,works like new,very happy thank you.

Removed the interior shelves and set screw which holds the light cover in place. Next I removed the four screws that hold the back panel in place. Located the defrost thermostat and removed it from the aluminum tubing by unclipping it, just as it was illustrated in the repair video. Cut the wires and stripped the ends and then connected them to the ends of the new defrost thermostat. Connected them together with an 16-14 gauge crimp style end cap. Taped the entry point into the end cap to reduce moisture penetration. Reassembled the back panel, light cover and shelves.

removed shelves and rear panel. cut wires, spliced in new part used wire nuts and filled wire nuts with silicone, replaced back panel and shelving

Removed the panel on the back wall inside the freezer side. To do this I unplugged the appliance, removed the racks, drawer, bulb and two screws holding the panel in place. The defrost cycle was not working so ice buildup on the coil was to the point of blocking air flow to the refrigerator side. I used a hair dryer set on high and stuffed two towels at the base of the coil to collect the melting frost and ice. Once the coil was clear of frost and ice I took the defrost timer off by sliding the clip off the tube, cut the wires and stripped the ends so I could use wire nuts to make the new connections . Placed the new defrost timer in the clip and reattached in the same location the old one was removed from. The sensor was replaced by doing the same steps. I replaced the panel after all the wire nuts were secured and the wires were tucked away where they would not interfere with the fan. Replaced the bulb, drawer, racks and food and plugged The refrigerator back in. 20 minutes from beginning to end.