GTS17BCSARWW General Electric Refrigerator - Instructions

Removed the old water valve from back of refrigerator by using a screwdriver. Pulled water line off old valve that runs into the fridge and inserted it into the new part. I used a pair of pliers to take off water line that runs into the water valve from the house. Screwed the water line back onto the new valve. Took about 10 minutes.

First I observe that the compressor motor is running since the freezer is cooling. The purchase of the condenser fan is initiated and when the part arrive it is just easy to reinstall the replacement condenser fan.

The problem on the front of the freezer door remains hot to touch and the compressor runs for a while and stop. The freezer is cold but still could not freeze the water. Inspection of the condenser fan reveals that it is not running. The order for the condenser fan from PARTSELECT came in a few days. Cleaning of the condenser of lint was first done and the process of removing the defective fan is just easy so with the installation.

The refrigerator as of now is running in perfect condition!

Did the repair just as the instruction said, once I read it. The part I didn't read was that if the plug was under the ice maker, you had to take the wire out of the clip on the side. So, had to dismount ice maker, unclip wire, remount maker, plug it in. Still under 30 minutes. Thank you.

First I removed the assembly by pulling it out of the back of the refrigerator at freezer height. Remove the clip from the old housing. I had already purchased the sticky pad that went on the back of the housing when I replace. After replacing your clip back onto the waterholes you could push it back into the refrigerator with no problem.

Went right on

replaced lights in refrigirator and freezer

After removing all items from the broken top, I removed both drawers and crisper top. I then slid the new top in place and replaced the drawers which easily slid into the grooves in the underside of the top.

I slid the old crisper drawer cover out, and slid the new one in. Then I respaced the other shelves, making room for the third shelf, and put the new shelf in. Apart from the time it took me to unpack the boxes these parts came in, and to remove my groceries from the fridge, the "repair" itself took all of about 90 seconds.

Installation could not have been easier!

Was only two screws after that carefully took the part away unplugging the wires at the same time was plugging in to the new part and was done after 5 or 7 min

I'm not a DIY-er, and wasn't sure a 20 year old refrigerator was worth the repair, but for $30 I could afford to be wrong. The swap is pretty intuitive, especially in my case since the problem was that the water tube from the valve to the ice maker had detached from the coupling. So I didn't have to cut anything off, just inserted the tube into the new valve. Reconnected the supply line, screwed the assembly back on the refer, and Bob's your uncle. Other than unloading some canned goods to lighten the refer, longest process was finding the right size nut driver in my disorganized tool tray. Be aware, there are NO instructions included with the part. Found a good video on you tube that confirmed the obvious. Glad I took a shot!

unplugged the old valve and disconnected the water line, then reconnected water line on new valve and plugged it in. It was an easy process but unfortunately that did not fix the problem. It is the ice maker it self so I will be ordering a replacement ice maker.

Remove the rear cover, shut off the water, removed the hose, unplugged the electrical connector, removed the screw holding the valve on. Removed the plastic tube going into the freezer and reversed the steps

First, I love that fact that my new fridge piece came in the mail in 2 days! I didn't order it as a rush, but I'm so glad it came so quickly! The installation could not have been easier! It took me longer to clear off my broken vegetable pan cover than it did to pop the new one in. My overall experience was amazing and super easy! I'll be back to PartSelect should I need I need to replace anything else in the future.

I must thank yo for sending the fan so fast. If I ever have to deal with any appliance again, you are first on my list.