GSE20IBTGFWW General Electric Refrigerator - Instructions

I followed the onsite video and had no problems. Shut off refrigerator, removed storage trays and bind, removed the rear panel under the light, identified the orange and pink electrical wires and cut them. Spliced the new wires of the thermostat with refrigerator wire and capped them, applied electrical tape to insure no moister makes contact with wires. Replaced rear panel and storage racks and bind. Plugged in the refrigerator and it is operations like new. I was about to purchase a new refrigerator for $ 1,300.00 and the thermostat costed $ 13.00. What a Christmas present!

Can’t repair it yet. Because it’s taking you too long to send me my parts. Tried calling but your answering service conveniently won’t answer. Had to cancel first order and reorder hopefully to receive faster.

Easy as 123

Each slide rail is secured by 2 Phillips screws. Remove the 2 Phillips screws on each slide rail. Reinstall in reverse manner of removal. A magnetized screwdriver is a big help for reinstalling the screws.

I made my wife fix it.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil

First I removed the two screws that held the old slide to the refer side wall, (after unloading the shelf and taking out the Veg. draw). I then put the screws in the new slide spots and screwed them into the refer wall using a hand screwdriver (phillips) and put everything back in place. It was about as simple a repair of anything I have had in the past 75 years. I didn't even have to swear.

Replaced both the Defrost Thermostat and Defrost Heating Element. The You Tube repair video clips were extremely helpful for both operations. My difficulty was getting access to the parts that needed to be replaced in a very tight side by side freezer space. Otherwise, the repair went smoothly and the refrigerator is back in normal operation in time to save the perishable food inside.

Removed the two drawers. Unscrewed the side rails that cracked away from the screws.Replaced the new side rails in place screwed in the screws and waalaa all done....easy as pie. Oh by the way I am a woman with little experience of tools...Just have to say the pictures of the parts made it really easy to pick out the correct part. Thanks

This was generally an easy fix. The work was in such a confined area of our side by side and my husbands shoulders are broad so that was a little more challenging but overall a quick, easy and cheap repair doing it ourselves without having to call a appliance repairman.

First take all your junk off the shelf (with the broken rail of course), take the glass shelf off. Remove screws (phillips). Throw away old rail. Replace new rail, tighten screws. Replace shelf, replace junk. You're done.

removed drawer, unscrewed old slide, screwed on new slide, voila! finished! I was very pleased with PartSelect -- ordering was easy, the correct part came quickly, and packaged very well. All of life should work so smoothly!