GFSL6KKYCLS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JAMES from MORENO VALLEY, CA
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water dispensed at a trickle
I only had to remove the old filter and install the new one - all by hand. I then ran about 1 to 1and1/2 gallons of water through the filter to clear it.
A WORD OF CAUTION - HOLD YOUR GLASS CLOSE TO THE WATER DISPENSER FOR THE INITIAL FILLING - IT WILL SPIT UNTIL THE AIR IS PURGED FROM THE SYSTEM!!!
An extremely easy repair.
A WORD OF CAUTION - HOLD YOUR GLASS CLOSE TO THE WATER DISPENSER FOR THE INITIAL FILLING - IT WILL SPIT UNTIL THE AIR IS PURGED FROM THE SYSTEM!!!
An extremely easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Libor from Danbury, CT
- Parts Used:
- DA81-01345B
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
door spring
replacing broken french door spring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from HAMPTON BAYS, NY
- Parts Used:
- WR60X10254, WR60X10255
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Warm refrigerator compartment.
Parts fit perfect. Very satisfied.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from OWASSO, OK
- Parts Used:
- WR17X12512
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Water flow 1 qt. Then slows
Water flow restrictions. Replaced flow valve. No help. Checked again and found filter head flow stopping valve broken. Replaced same. All good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from BAY VILLAGE, OH
- Parts Used:
- WR13X10738
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replace ice chute assembly on GE Profile frig.
I was not able to repair or find any info on line on how to remove control panel. Hired a local appliance tech for $117 and after much trouble he was able to release two tabs on right side of control panel with small screwdriver for low tab and long rod on upper tab. After panel is off new part replacement is easy. This GE frig ice chute is much different than new models. The whole assembly is replaced not just the flapper and solenoid. Be careful to not break control panel while removing. I very stupid design as far as easy service. Also screw on underside is removed first. GE could have made repair easier with good engineering.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from NORTHWOOD, NH
- Parts Used:
- DA81-01345B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Just follow instructions. Easy
Held spring with needle nose pliers and slipped into place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from EAST HARTFORD, CT
- Parts Used:
- DA81-01345B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Door flap would not close properly
Show how to fix it on YouTube so that helped a lot. I ordered a new spring gave all the correct information and the spring was too big that showed up
lol so had to go to Plan B an modified the broken spring lol works great now
lol so had to go to Plan B an modified the broken spring lol works great now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from CLIFTON PARK, NY
- Parts Used:
- WR30X10131
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Icemaker worked except for warming coil which prevented ice from releasing into tray
Replacement ice maker was plug in unit, only needed to remove one screw holding plastic plate that hid plug and wiring. Plugged it in and reattached plate with screw and done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from AUSTIN, TX
- Parts Used:
- DA81-01345B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original spring broke
Used a pair of needle nose pliers and replaced the spring.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from DEFIANCE, OH
- Parts Used:
- WR30X10131
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Maker stopped workiing
Hardest part of repair was getting frig. away from cabinets to unplug it.
Turn off water to ice maker.
Phillips's screwdriver to take off the cover of the electrical connection to
the icemaker tip it outward. I used flat head screwdriver to help disconnect the connection.
Also, to help getting the old icemaker removed. Once removed returned New one the reverse of taking it out. Won't need screwdriver to get it back in place. Put cover back in place and put the Phillips screw back in place. Plug refrig. back in. put it back in place turn the water back on should be good to go! BE afew hrs. before ice starts to show up!
Good Luck
Turn off water to ice maker.
Phillips's screwdriver to take off the cover of the electrical connection to
the icemaker tip it outward. I used flat head screwdriver to help disconnect the connection.
Also, to help getting the old icemaker removed. Once removed returned New one the reverse of taking it out. Won't need screwdriver to get it back in place. Put cover back in place and put the Phillips screw back in place. Plug refrig. back in. put it back in place turn the water back on should be good to go! BE afew hrs. before ice starts to show up!
Good Luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from BUTTE, MT
- Parts Used:
- DA81-01345B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door
Replaced the spring on my French door refrigerator
Was super easy
Was super easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Kingsport, TN
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scheduled replacement
Turned the old filter loose, removed the adapter from it, put the adapter on the new filter and turned the new filter back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rene from Lancaster, CA
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water flow from in-door dispenser was a trickle
We didn't think the dispenser problem was related to the filter - we were wrong! It took less than two minutes, including opening the box and unwrapping the filter. I'll definitely be changing my filter more often - and buying it through PartSelect. Your ordering was so easy and delivery was unbelievably fast!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William c.. from Barberton, OH
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water leak
got new filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from San Antonio, TX
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
There is no problem since it is time to change filter.
Just turn the cartilage out and put the new one. Very simple
Was this instruction helpful to you?
Thank you for voting!