GDL22KCWBSS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dan from COLUMBIA, SC
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Refrigerator not getting cold
Replaced Temperature Sensor and now it is getting cold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Lewes, DE
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
no water to icemaker
removed back cover--disconnect water supply-- removed screw holding vave and unplugged the
electric from the valve-- disconncect waterline to
the icemaker. reverse the to put on new part.
electric from the valve-- disconncect waterline to
the icemaker. reverse the to put on new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willie from Virginia Beach, VA
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Ice maker traydid not fill with water
Unplug electrical power to refrigerator. Disconnected electrical power to water valve, Disconnected water inlet and out let lines from valve. Remove screw holding valve on refrigerator, removed and replaced water valve with screw. Connected inlet and outlet water lines, turned on water and checked for leaks. Connected electrical power to water valve, plug in electrical power to the refrogerator. Ice maker tray fill, made ice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Port Republic, MD
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
Small Ice cubes/Jams
My Son removed two screws, electric plug and two (2) compresion nuts. He had to bend the bracket to fit, then replace it, in reverse order except the filler tube on the new valve was of a "stabb-in" type. Job was a piece of cake and this small project, solved all our problems with the Ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kent from Bartlesville, OK
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Freezer working but fridge not cooling.
Totally followed the instructions of the video that came with the sensor. Unplugged the the fridge, defrosted the freezer. Cut off the main sensor that usually is the one that goes out. Installed the the new sensor with new wire terminals, crimped them and covered with electrical tape. Fridge works like a charm. Partsselect is excellent. Saved me a few hundred dollars versus having a GE Tech come and do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from Sanford, NC
- Parts Used:
- WR57X10033
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
valve wouldn't allow enough water to fill ice maker.
Started with a visual inspection.
Turned off water.
Removed old valve.
Bent bracket to facilitate installation.
Installed.
Hooked up.
Tested.
Works as advertised.....
Turned off water.
Removed old valve.
Bent bracket to facilitate installation.
Installed.
Hooked up.
Tested.
Works as advertised.....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Severna park, MD
- Parts Used:
- WR14X10177
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Seal on freezer. Broken
Cleaned mating surfaces with acetone using vapor mask because done indoors. No instructions as to which cleaner to clean old glue off. Matting surfaces. No nistructions as to what glue to use so used silicone. We'll see if it holds up
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANK M from EASTON, PA
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Ice Maker was not working
1st - checked water supply - old valve in water line was closed with sediment.
2nd - replaced water line valve and reconnected copper tubing about 1 hour
3rd. removed single outlet valve and installed the new part - about 15 minutes
Everything went well and was very easy.
Unfortunately, the ice maker still does not work.
Still trying to understand what is wrong.
2nd - replaced water line valve and reconnected copper tubing about 1 hour
3rd. removed single outlet valve and installed the new part - about 15 minutes
Everything went well and was very easy.
Unfortunately, the ice maker still does not work.
Still trying to understand what is wrong.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- QUOC-LOC from LYNN HAVEN, FL
- Parts Used:
- WR55X24064
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The control board generated clicking noise. Temperature display wrong values.
On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Lake Helen, FL
- Parts Used:
- WR57X10033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Mounting bracket did not fit. Retainer for water input looked like a thread protector.
Put bracket on workbench and hit two or three times with hammer. Glad I did not remove water inlet retainer from part, it can very easily be mistaken for a thread protector.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Crawfordsville, IN
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
No water to icemaker
Shut the water off, removed two screws,removed the inlet, from the water valve then the line from the valve to the ice maker. Then you reverce these steps and you are done. The shipping time was the best I have ever seen. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- larrie from punta gorda, FL
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
ice maker just stopped
part arrived on schedule,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lana from Fort Myers, FL
- Parts Used:
- WR29X10092
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The fill cup kept breaking and we couldn't find the part. Did a google search and found Partselect.com who had it.
Slide it over the fill hose and just line it up and put it in the slot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- olin from forest city, NC
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker not working
First i shut the water valve off going to the fridge, I then removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then i took the water line loose to the element, reverse the prosses and put all back on new element and installed,
Was this instruction helpful to you?
Thank you for voting!