GCE23LBWHFBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Phoenix, AZ
- Parts Used:
- WR71X10979, WR71X10761
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
no shelf
Installed shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Phoenix, AZ
- Parts Used:
- WR71X10973
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
missing Door bin
I just installed the bin in the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zachary from Decatur, GA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Fridge was freezing food near the back, adjusting internal temp not fixing the problem
Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis P from Southwick, MA
- Parts Used:
- WR11X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
broken door lever
slipped the part in , attached the spring, that was all it took
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Oceanside, OR
- Parts Used:
- WR71X10761
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf insert, needed replacing.
Removed broken panel, replaced with new piece. Took about 1 minute. Thanks for making such simple fixes available to the DIY people who need affordable repairs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Naples, FL
- Parts Used:
- WR74X10270
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Grille was evidently damaged while moving refrig.....
and a rat recently got trapped in the house while the owner was away. The rat chewed the grill quite a bit too. The repair was accomplished using a phillips screwdriver on the two screws which attach the grille to the refrig.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAUL from Katy, TX
- Parts Used:
- WR71X10761
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Insert
Snapped in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ford Blunt from CEDAR HILL, TX
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Switch stopped working
Used screw driver to lightly remove the old switch. Disconnected the 2 electrical leads to the old switch, then I connected those leads to the new switch. The light immediately came back on and I placed the switch into its housing hole and popped it in place. It works perfectly now. My wife said "let there be light"! Very easy installation. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Rancho Cordova, CA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator freezing.
Temp. Sensor was under an egg shaped cover on the left side wall in the refrigerator. Remove the cover, cut the two wires to the old sensor and remove it. Connect the new sensor to the two wires using butt connectors. Replace cover and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANTHONY from WOLCOTT, CT
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light switch broke
i followed all the other submited solutions. really easy. popped out the broken light switch with thin tip screwdriver. careful not to let wires slip into compartment. then attached wires as i pulled them off broken switch. then carefully pop the new switch back in the slot. when i was younger i worked for an appliance repair company. i felt confident in this repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from WILLIAMSBURG, VA
- Parts Used:
- WR23X21444
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
light switch in freezer broke
Used small screw driver to pry the top of the switch away from left inside wall of freezer side of side-by-side refrig./freezer; then used pliers to remove the switch; then removed the 3 prong socket and plugged it to new switch and installed it into the inside wall of the freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Nesquehoning, PA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fridge wouldn't keep temp
My son replaced both temperature sensors and the fridge works great now!!! Like brand new again!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendell from Baton Rouge, LA
- Parts Used:
- WR60X24484, WR02X12149
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rat chewed up fan blades in refrigerator at our camp.
We just pried off the fan blades and pushed on the new part. Could not have been easier. The rat has been permanently dipatched and, hopefully, that is that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Titusville, FL
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dropped a glass bowl hitting and breaking off the light switch.
Ordered the part and within three working days the part was delivered. It took two minutes to pry off the broken part and one minute to snap in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roman from Fort Worth, TX
- Parts Used:
- WR23X31507
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light switch was broken
replaced with new one
Was this instruction helpful to you?
Thank you for voting!