DTH18ZBXCRWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Anthony from Riverview, FL
- Parts Used:
- WR02X10740
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
frig door kept slamming into cabinet
took the old stop off put the new stop on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Painter, VA
- Parts Used:
- WR72X10086
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
broking slide
replace the bar lift top off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenroy from Martinsburg, WV
- Parts Used:
- WR60X10205, WR02X10098
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The refrigerator made a humming/grinding sound
I used the socket set to remove pannel that allowed me to have access to the evaporator fan. Once the fan and it's container was visible, I removed the entire fan container using the socket set. I took the fan out of the container, removed the damage blade and the damaged fan grommets. I then replace the old blade with the new blade and put the fan and the compartment back together. I am not very handy so if I am able to do this, anybody can. Ps. I was very very pleased with the services I received from PartSelect and would encourage others to use them - must admit I was very suspicious at first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from PIONEERTOWN, CA
- Parts Used:
- WR60X10348, WR02X12149, WR02X10098
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Fan motor noisy
Turn off refrigerator. Remove the plastic air flow cover, styrofoam channel and metal panel inside freezer compartment, remove hex nuts holding motor mount, unplug connector, remove old grommets, remove compression ring, (note 1/4 inch extension of shaft through fan) carefully pull fan blade off motor shaft and put on new motor shaft, leaving 1/4 inch of shaft extending through, replace compression ring. If your new fan motor has a female snap connector and the old motor has a male connector (as mine did) you will have to cut the wires on both new and old motors, splice and solder the male connector onto the wires of new motor, wrap carefully with premium electrical tape (or shrink tubing). Replace the 2 grommets, Reconnect the fan and bolt back into place. Make sure all the bolts around the mount are tight. Replace the metal panel. Manually spin the fan making sure it is free of the shroud. If it binds in the shroud, physically move the motor and mount till it rotates freely. Turn on refrigerator and test fan operation. If it's all good, replace the styrofoam and plastic cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Penny from Gilbert, AZ
- Parts Used:
- WR72X10086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic slide for snack pan right side cracked/broke
Only took a screwdriver to take two screws out & install new slide with the two existing screws. Very easy. Took less than 5 minutes. Great website I found on Google right away, just by searching for refridgerator parts. After ordering part, only took a few days to come in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Clayton, NC
- Parts Used:
- WR32X10537
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken frame for crisper bins
Using Google search engine I was able to quickly locate the replacement rack for the refrigerator. When it arrived, I installed it by attaching it to the interior frame of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jules from Crowley, LA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
failed light switch
I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from collegeville, PA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no light in freezer
Connected the 2 wires and pushed in the switch until it clicked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwight from Indianapolis, IN
- Parts Used:
- WR71X10702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
new refrigator purchased had no freezer shelf
Shelf easily went in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Redmond, WA
- Parts Used:
- WR24X10186, WR24X10187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The refrigerator and freezer door gasket's were leaking
The repair is very simple, the gasket sits in a channel in the door. Just start with a corner and pull the old gasket out. Once you've removed the old gasket, push the new gasket into the same channel. Make sure you've completely pushed in the new gasket all the way around the door. It's as simple as that. The repair takes less than 5 minutes per door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from San Marcos, TX
- Parts Used:
- WR72X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Snack Pan Slide
2 screws. how easy can i get.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Seatac, WA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
switch wouldn't come out anymore and turn light on
Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from Oak Ridge, NJ
- Parts Used:
- WR32X10537
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Shelf above vegetable drawers cracked in middle
Take out both vegetable drawers. Lift back of shelf first then front until you hear the click from both front sides. The shelf should now be loose and you can take fully out. Remove the glass shelf from the plastic frame by turning the shelf over and pulling back and up from the rear part of the glass. Put the glass into the new plastic frame by doing the same technique. Then put the shelf back into the fridge by the resting the shelf down in the correct position and pushing the front of the shelf until you hear the click again on each side. slide the drawers back into place and you are done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Simpsonville, SC
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light switch quit working
removed the inside fridge electrical panel and swapped switches
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANTHONY from NEW EGYPT, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
sticky switch
easy pry out, disconnect wiring, connect on new switch and press in switch.
Was this instruction helpful to you?
Thank you for voting!