CFCP1NIZBSS General Electric Refrigerator - Instructions

After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.

The problem was both the valve and a frozen slug of water in the supply line located inside the door. After replacing the valve, I turned the freezer to a setting of 1 and in about 30 hours, water flowed out the tap.

Followed the video showing how it was done. Took me longer to go to the basement and shut the water off and on, than it did to replace the valve

Unplugged ref.,turnned water off at wall and drained, removed back cover on lower part of ref. then removed screw holding water valve,unplugged both wires from unit,pulled the 3 water lines off,1 I had to cut, would not release,got new water valve,push 3 water lines in place,attached the 2 wires in place and screwed unit back on ref.and replaced back cover on ref. Then I got a hair dryer and thawed all ice that had built up behind and under ice maker in freezer,cleaned that mess up,turned water back on plugged in ref. All good ,repaired problem,old water valve was bad.

It's a very easy repair. However, there are no installation instructions included with the gaskets. Per videos I watched, it recommended that the gaskets be soaked in warm / hot water to make them more pliable when installing. Unfortunately, after installing the refrigerator gaskets, there were gaps that I could not seal resulting in an interior temperature of 48 degrees. For some reason, the gaskets appeared to be puckered thereby preventing a decent seal. I don't know if the puckering was caused by the soaking. I ended up reinstalling the old gaskets.

Show installation!

Removed back wall cover over coil. Defrost all ice with a hair dryer. Cut white wires and replaced Temperature Sensor. It has been working for a week and no trouble at this time. If you have this system on your GE refrigerator do this before replacing the motherboard. I must admit I was thinking that was the trouble. Motherboard was replaced after 5 years old now 5 years later my thinking is this a 5 year problem. So try the Temperature Sensor.

Of course being a women to say I repair my refrigirator is very self gratifying specially when share with other womens like me divorce,having to do on their own, great site, very simple explain on the video with words I could understand, no surprices right to the penny. I save a lot of money, thank you so much, i recomend the site to anybody.

Shut water behind the refrigerator, unplugged the unit. Unscrewed the back tin panel and simply unscrewed the brace scew for the Double Outlet Water Valve. Disconnected the hoss - inspected the hosed for wear. Next detached the hoses and power source to the unit... reconnected both hoses & power source, plug the refrigator back in and inspected for any water leaks. Simple!

Watch G.E refrigerator troubleshooting guide from partselect.com. made necessary cks.called part select discuss finding determined cause order part, paid extra $10.00 for 2 day shipping spent total $93.00 plug unit into side of compressor ,unit operating great .8 hrs. later freezer 0° ref.36°.
Note:
Contacted two different appliances repair co.,both 2days to schedule repair time, both cost over $350.00 repair costs, don't know if that included taxs.

Nothing to tell it was just a replacement part that the old part was removed and the new one inserted. Works like a dream Thanks

Just fallow video shows that it 123 !

This is a simple repair. You remove the two upper crisper drawers, remove the bottom slide draw that holds cheese, etc. Then lift up on the crisper pan cover and pull out. Note: the old crisper pan will have 2 rubber moldings you will need to move to the new one and there is a sponge molding that if you peel off very carefully you can put on the new pan otherwise you will need to buy that. No one told me that and I wish they did... so that is why I am writing this.

We actually followed the instructions of the video for the installation of the dual inlet valve and it was incredibly easy to perform. The fridge works perfect again!

Removed the entire dairy shelf from door and installed the dairy door and replaced the entire dairy compartment on door