PFIC1NFWABV General Electric Refrigerator - Instructions

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

Removed mother board and replaced. Working fine now

Remove the shelves then remove the back by removing the two screws at the top of the panel. Locate the temperature sensor on top of the coil. Cut the wires and replace with the new one. Use wire nuts and electrical tape to reconnect the wires.

The problem began when freezer thawed and could not keep food frozen. Initially, I thought the issue was the defrost heater (because I had seen similar symptoms previously and resolved the issue with a new defrost heater)and I replaced that part with a spare that I had puchased previously. The issue was still unresolved and I noticed the evaporator fan was not running in the freezer because it would not turn on when I closed the door. I checked to make sure I could hear the compressor working (and it was)and concluded that the evaporator fan motor was not running. I ordered the part and found a YouTube DIY video on how to replace it. While I was at work, my fiancee took it upon herself to watch the installation video and install the new evaporator fan motor and all is well.

I decided to replace motor and fan, having previously altered/trimmed the fan which stopped the howling but caused a vibration. Unplug from mains. Clear out two top shelves in freezer. Remove light cover. Remove two screws(1/4 driver)at top of steel panel in rear of compartment and let it drop. Remove two screws above light. Pry up section above light/fan housing to access two screws retaining the light/fan assembly, loosen screws sufficiently so that assembly can be lifted and removed. Disconnect wiring plug by pinching in the sides of the plug and pulling out. Pull fan off motor shaft. Remove two screws clamping motor. Cut cable tie and molded wiring grommet to free wiring. The existing light wires can be removed from the old plug by carefully cutting around the old plug to free the pins and then pushing the pins into the new plug. Reverse procedure to assemble.

replace sensor in refriger.

Then I fixed it.

replaced the icemaker inlet valve. works like a champ now

Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold

I had replaced the sensors, thermostat and evaporater heater without correcting the problem. Decided to try the control board. The main problem has been the ice in icemaker melting every couple of days and thawing all over the freezer food. The top part of the freezer compartment thawed with less thawing in the lower section. Removed back metal cover. Unplugged fridge, took picture of control board to remember locations of connections. Never needed it though as I took caution to remember the different connections. Unplugged all of the connections and then took needle nose pliers to depress the 4 pins holding the control board in place one at a time. This was a bit difficult and you will need to exercise patience. Not my long suit. Eventually I depressed the pins correctly and got the old control board to slide out. Replaced with new control board and re-connected all the wire harnesses. They actually slide on pretty easily if you have them in the correct position. I also had taken all the food out of the freezer and removed the cover to the evaporator which was iced up. Took a hair dryer and thawed all the ice before re-starting the fridge to give it a nice clean start. Replaced the back panel and plugged in the fridge. 4 days now and it is running great so far. A lot quieter than before.

it was easy the only thing was i had to cut old harness to remove 2 wires that went to coil that had to go back in the new harness other then that a peice of cake.

Little difficult getting the switch out, had to pry wth some force. New installation was real easy.

i followed a video that was on your site, the video couldn't have been easier to follow it was step by step and very easy to follow, i replaced the evaporator fan motor and everything is working fine, i did notice that the evaporator coil was frozen pretty bad when i removed the back freezer panel i am going to check it again in a couple of weeks to make sure i don't have a defrosting problem as of now everything is fine i am hoping it was just the bad fan motor causing the coil to freeze up because of no air movement over the coil

My refrigerator was making a high pitched kind of howling noise. The PartSelect symptom that was closest was “unusual noise” and when I clicked that it said the evaporator fan motor fixes the symptom 32% of the time. Since my freezer fan speed sounded like it was constantly changing I went ahead and bought one which PartSelect delivered promptly. The installation video was great and although my freezer was not identical to the one in the video, the video was still very helpful. The only thing it didn’t say was how to tell if my freezer motor was the one with the thermistor although I suspect that they all are and that PartSelect is simply trying to save us money by showing us how to splice in a motor without a thermistor. Anyway, since I would have had to disassemble the freezer before buying the part to find out for sure, I just bought the one without the thermistor. This just meant I had to splice the new motor in, just like in the video. I think I would have preferred buying the motor with the thermistor even though it was more expensive. In the end my problem is solved so I’m happy. This is the third time that I’ve had to repair this GE refrigerator and PartSelect has been a valuable resource each time.

followed you online video and it was easy and simple repair only took about an hour frig is back quiet and working fine thanks also parts come fast