GBS22HCPACC General Electric Refrigerator - Instructions

according to the vidio showing how to to change the control board its look relatively easy i dont think i will have a problem changing it ,,but will i change the right part for the problem " the frige take to long to get cold again after thrawing state freezer temperature went up to 19 * or more sometime ,,thermostat has been changed and its solved the ice deposit problem" hopefully changing the control board will help shorting the long thrawing state" the board has not been changed cause the frige start working again

I ensured that the refrigerator was unplugged from the power, removed the main board enclosure cover, carefully unplugged the wiring connectors from the board, released the 4 plastic standoffs with needle nosed pliers by gently squeezing the ends and removed the board.
I placed the new Main Control Board on the standoffs, carefully re-connected the electrical connectors, ensuring that the plugs were mated correctly, replaced the board enclosure cover and powered up the refrigerator to verify operation of the compressor, fans and controls.
Once verified, I unplugged the refrigerator from the power, removed the access cover to the compressor and condenser and carefully cleaned all dust and lint from the back and underside of the refrigerator before replacing the cover and putting the refrigerator back into service.
The cleaning will improve the efficient operation of the refrigerator.

Checked this website for symptoms described, found same descrip, ordered mainboard, changed out in less then 30 minutes, Frig working properly now. Follow the installation instructions carefully as this mainboard fits other frig's & depending on model some wires need to be cut on harness etc.

Having been in the h vac field for thirty years,I started looking for the defrost timer and found the circuit board. I went on-line and found PartSelect. The site was very helpful in helping me to find the part I needed.The clips were a little hard to get off the old board, but besides that the installation was pretty easy.

Removed small panel on back of refrigerator, lower right hand side as you face the back. Removed old mother board and installed new one per provided instructions. Ice/water dispenser operation returned to noraml. The only tricky part is removing the motherboard because it's held in with platic clips that have to be pinched with pliers in order to slide the motherboard over them. Look carefully and you'll see which way to pinch them.

Replaced circuit board / fixed problem

The freezer kept getting to warm (up to 28 degrees at times on the digital display). We took the cover off the main control board, and if we pushed on one of the connections it would start the condenser. Sometimes the freezer would work for several weeks, and then have trouble for a week.

Finally we got tired of "baby-sitting" the fridge, and sent for a new main control board. Installed in about 15 minutes, and so far the everything is working great.

Moved fridge out from wall. Unplugged. Removed circuitboard cover 6 screws?). Replaced circuit board (showed burn spots on back side). Replaced cover and plugged back in.

was not home when part came so my wife installed it enough said

I found a burn solder on the main board.
replace it. works again.

Removed broken part from refrigerator.
Removed 2 plastic parts and tempered glass shelf
and installed on new part.
Change out went OK.
A few tools and some patience

Job complete

first empty both sides then took apart freezer area ice maker-light cover-back cover and exposed fanchecked all connections ordered fan[had no amp probe to see if power at motor repaceed fan still fan didnot runmoved fridg out from wall found control board didnt find any thing wrongto the eye ordered control board remove all connectionsused plyers be easy to remove from board squezed little whit tabs[3 or 4] to remove board from fridge installed new board snapping the pegs back into holes then reinstallwire connectors [ps the board comes with a few extra ports dont worryjust connect to the ones on the old board] dont forget to hook up green groung wire when you put cover back on then plug in and turned on closed up the freezer and reinstalled icemaker and other parts started and all seems ok good luck

Unplugged side by side took about 4-5 screws out removed plate from back, unplugged the wires removed old board and plugged wires in new board, note: new board a little different than original. Screwed plate back in. So far so good. I do not think I will buy any more ge appliances, this one was very expensive but out of warranty now my ge dishwasher is making noise all purchased at same time.

I unplugged the unit, replaced the main board, repowered and observe for a few minutes. my fridge is okay again.

read on line that fan control in main board can cause erratic running of the fan causing "whooing" and ghostly sounds. New board installed and now I have the quietest fridge in the neighborhood. Here's the unbelieveable part. Ordered the part online from parts select on good friday morning. Fed ex delivered it just after lunch the next day (saturday). Now that's the best service I've ever received!!