TFX27FKC General Electric Refrigerator - Instructions

I'm a housewife in her late 40's. Before ordering the part, I watched your video on how to remove and install the new icemaker. First I unplugged the refrigerator. After a few minutes, I unplugged the icemaker and unscrewed it. I lifted it a bit and removed it. I did not use the icecup that comes with the part. Instead I removed the one from the old part and inserted it to the new one. Then I plugged in the new icemaker, placed it inside so as to match the holes and screwed it in. YES, it was that simple. It took me less than 10 minutes to do this. I saved myself over $100!!

I opened the package and screwed the rails in. The first repair rail kit included extra screws, the last did not so don't toss the existing screws.

Removed broken light cover (that was held together with tape) and replaced with new part. The most amazing thing was that I was able to locate the part for a 21 year old refrigerator

Quite easy. Turn off water supply and turn off ice maker at switch inside freezer. Unscrew the old unit, separate the electrical connection, and pull it out. New unit comes with parts that do not fit my refrigerator, so visually examine the new and old units, reuse any needed parts from the old unit, such as plastic water ramp. Reconnect the electrical connector, and screw it back in. Turn water supply back on and then turn ice maker back on at switch inside freezer. Discard unused parts. Wait up to 24 hours for new ice cubes to be made.

Literally took out one screw and a wiring harness. Removed the old plastic piece off of the old ice maker and put on the new one.Installed new ice maker with the one screw and plugged the wiring back in.DONE!

The replacement part came with a one page instruction sheet. Following those instructions I cut the two hoses on the old resivour and removed it. I then cut the hoses on the new resivour to desired length (all inside the refrigerator). Using the two couplers provided with the new resivour I hocked the two hoses together and tightened them with a wrench. It took longer to clean the refrigerator than it did to replace the part. Instruction sheet was very helpful

Removed the faulty ice maker in about two min.. New unit was installed in approx. five min. Watched your video prior to installation and it helped greatly.

I read the step by step instructions that came with the part. I turned two screws and disconnected the electrical harness and Removed the icemaker. Two other parts from the old icemaker were easily removed without any tools and put on the new icemaker. The new icemaker was put in the same way the old one came out. I reconnected the electrical harness and tightened the old screws. The hardest part of the whole job was reading the directions. They were easy to follow if you take the time to Just read them!

Piece of cake and now I get loads of ice.

unscrew one screw unplug.insert the ice maker,put the screw back in you have ice less than ten minutes

Seemed simple and intuitive B U T the water tube receiver fooled me. Seemed to be on backwards. So, like my wife suggested, I D I D then read the installation instructions. Yeah! It's amazing what you can do when you just RTI. :-0

Followed the instructions. Smooth as silk. This part is better than the original. There appears to be a sensor that beeps when the ice reservoir is full.

Followed the video demo and would have been done sooner but for limited work space- narrow freezer compartment and the release tabs on the electrical plug. First home repair that the air was not blue and got done in under time allocated.

I spent 15 - 20 minutes just hunting/deciding which of several sets of parts & directions to follow. The provided directions were not bad; but none of them quite matched my GE ADORA side-by-side model. Once I came up with the actions I would need to take...I was done in 5 minutes! The kit , as I said, came with all the parts one could need (and one or two un-needed parts included for other model GE refrigerators) I am very happy with PART SELECT...altough GE doesn't rate as high with me for their declining reliability.

I just followed the directions carefully, loosened the screws with a nutdriver removed the unit from the screws, unplugged the unit from the freezer plug, took out the new unit, used the adapter supplied with the unit to match up with the plug in the freezer, carefully attached the icemaking unit to the screws, carefully slid the cord behind the unit, lightly clinched down the screws, checked it with a level and then did the final snug down. turned the unit on and it worked fine. Pretty easy, just take your time, don't rush and it will come out fine.