GSA20IBPCFWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Troy from Dacula, GA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Food section of fridge always warm
Located temperature sensor on condenser in the freezer section( as per instructional video ). Cut off bad sensor with wire cutter then soldered on the new sensor and sealed with electrical shrink wrap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John J. from Deland, FL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
freezer no cold enought
as per video- follow all of the videos and u r going to save a lot of money tx partselect im glad I found u guys ps only order from partselect.com they only ship the correct parts remember look at the video select the symptom and buy as per video tx again problemsolved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ajaykumar from Plainsboro, NJ
- Parts Used:
- WR60X10209
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The refrigerator was making load and unusual noises.
I identified the noise was coming from the coils / and the fan. Cleaning the fan helped reduce the noise a bit but it still kept recurring. I ordered the part, which was really easy using the diagram on the website. The instructions and the video were really helpful and was able to remove the old motor and replace it with the new one with relative ease. While there I cleaned the fan blade and vacuumed the surrounding area. This whole repair went quite smoothly and has given me the confidence to take on other repairs before calling out the repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gene from Pocatello, ID
- Parts Used:
- WR50X10068, WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The temperature in the refreezer and refrigerator was slowly getting warmer although the condensor motor was running continually.
Unplug the refrigerator and remove frozen food, shelving, light and back panel inside the freezer section to expose the cooling coils. The coils were completely iced over. Using a wet dry vacuum to discharge the air toward the coils quickly melted the ice. The trouble shooting section on your website described my problem and I bought both items which were the most common problem. Using the video(s) e-mailed to me when purchasing the parts provided great information regarding details for the repair. After replacing both parts the refrigerator is working great having spent just under $25.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marciano from Phoenix, AZ
- Parts Used:
- WR50X10068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Freezer wouldn't freeze
With my hands and tools. It was real easy. Now just waiting to see it that was the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Silvio from Rolesville, NC
- Parts Used:
- WR50X10068, WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
defrost would't work on side-by-side refrigerator
My defrost was not working, so from time to time I had to remove the accumulated ice with a hair dryer. I did some research and found out it is typically caused by a failing defrost thermostat, or temperature sensor. I purchase and replaced both for 30 dollars. Really easy. I watched the instruction videos on the site at least 5 times, so when I did it, it was like I was doing for the 5th time. Now the fridge works just fine!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darryl from Weatherly, PA
- Parts Used:
- WR50X10068, WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refrigerator side was not cooling
Removed the panel on the back wall inside the freezer side. To do this I unplugged the appliance, removed the racks, drawer, bulb and two screws holding the panel in place. The defrost cycle was not working so ice buildup on the coil was to the point of blocking air flow to the refrigerator side. I used a hair dryer set on high and stuffed two towels at the base of the coil to collect the melting frost and ice. Once the coil was clear of frost and ice I took the defrost timer off by sliding the clip off the tube, cut the wires and stripped the ends so I could use wire nuts to make the new connections . Placed the new defrost timer in the clip and reattached in the same location the old one was removed from. The sensor was replaced by doing the same steps. I replaced the panel after all the wire nuts were secured and the wires were tucked away where they would not interfere with the fan. Replaced the bulb, drawer, racks and food and plugged The refrigerator back in. 20 minutes from beginning to end.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Whittier, CA
- Parts Used:
- WR50X10068
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
fridge and freezer not staying cold
removed back panel from freezer. located thermostat removed and replaced thermostat put panel and all baskets back into freezer and plugged fridge back in. Works perfect problem solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- philip from cocoa, FL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer would not defrost
There were only 3parts listed to check omed out the defrost heater and thermostat ....thermistor checked bad ordered replacement took less than 2 minutes to replace after I defrosted it again runs fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Orlando, FL
- Parts Used:
- WR50X10068
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
refrig not turning off and defrosting
replaced the defrost thermostat. The "how to" video was superb. Watched it twice before beginning the job. repair went as described.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HALLER from WESTVILLE, IN
- Parts Used:
- WR32X10141, WR14X10085
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace edge and glass shelf
This was very easy to replace the broken shelf, just place the protective rubber edge on the glass shelf and place in refrigerator. I LOVE THE THOUGHT THAT i COULD ORDER THE PART AND HAVE IT DELIVERED TO MY DOOR AND BE DONE! THANK YOU
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Saint Charles, IL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
refrige ws too cold
as per video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- khampheuy from Kerrville, TX
- Parts Used:
- WR50X10068
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Frige was warm and Freezer was freezing up
I have checked the defrost thermostat:During the defrosting cycle the thermostat is still open
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Rancho Cordova, CA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator freezing.
Temp. Sensor was under an egg shaped cover on the left side wall in the refrigerator. Remove the cover, cut the two wires to the old sensor and remove it. Connect the new sensor to the two wires using butt connectors. Replace cover and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Copperhill, TN
- Parts Used:
- WR22X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
one of the holes was broken
took the old one out and replaced it with the new one, then trashed the old one
Was this instruction helpful to you?
Thank you for voting!