GSE20IBTBFWW General Electric Refrigerator - Instructions

Unplug the refrigerator. Pull all shelves out of the freezer. Remove light bulb shield and light bulb. Remove the two hex head screws on either side of the light bulb. Wiggle out the back wall. It is a tight sqeeze, but can be done. Locate the sensor on the top of the coils. It is held on by a simple clip. Wiggle the sensor and twist a little to take it off. Take wire cutters and cut the two wires into the sensor near the sensor to allow lots of room to splice in the new sensor. Strip about a quarter inch of wires left in the freezer. Use some sort of wire connectors, like twist caps, which will allow you to connect the two wires to the new sensor. Make sure to match the colors. I used shrink tube and line connectors. Once you have the new wires spliced together and protected with either shrink tube or electrical tape, tuck the excess wire out of the way and attach the new sensor. This is easily done by slight pressure on the sensor with the tube in between the clip and sensor. Make sure the wires are tuck out of the way and reassemble the freezer panel, light bulb, and shelves in the reverse order.

Refrigerator was showing actual temperature of 80 deg, freezer was about 3 deg high. (house temp was 65 at the time) Defrost heater seemed like the only component able to heat that much, so the defrost thermostat seemed like the likely culprit. I followed the installation directions in the video, and the fridge has been fine ever since.

I ordered the part but my husband had to work out of town for a week. The fridge kept getting warmer, so when the part came I just watched the video on the internet, (bit the bullet) and did the repair just as I saw it done on the video. It was simple and exactly the same as the video. It took a little longer for me because there was a lot of ice built up on the coils, so I used my hair dryer to melt the ice. My refridgerator is working great now.

I followed the instructional video. It was right on the money for accuracy in terms of part location and method of replacement.

3 weeks After changing the defrost heater, i had to change the thermostat, part was suppose to come with wire connectors and everything needed, it didn't. Cut two wires to old thermostst, strip about a 1/4 inch of insulation and crimp new wires on part together. cover with heat shrink and heat with lighter until sealed.

I took the ice maker out then the panels that closes in the evaporator coil. Disconnected the defrost censer and tested it with an ice bath. The censer did not close the circuit. So it's bad. I got the parts .(Very fast I might add. The PartSelect team did a great job of getting it to me). I the stripped the wires and spliced the like colors back together and tested the censer again with an ice bath. It closed this time. I started the frig and have not heard anything from the client. In this case "No news is good news". Thanks PartSelect

Removed food from Freezer, Unplugged refrigerator. Removed light bulb cover and ligt bulb. Unplugged and removed Ice maker and motor. Removed air duct cover from motor. Unplugged and removed evaporator housing and fan. Pulled fan blade off. Unscrewed brackets from fan motor, removed dust cap from top of motor and grommet from bottom. New motor came with 6 pin connector and four pins for evaporator fan motor. Cut the harness grommet to separate the light bulb wiring from the evaporator motor's. Pushed the the old light bulb pins (red and orange) from old connector and push them in to the new fan motor connector. Reversed the process and no more noise

I watched the online video on how to replace a defrost limiter. It was almost exactly like my situation and made the job seem familiar. It was inexpensive ($8 part)and easy to do.

I took off the back panel in the freezer. Located the wires going to the old thermostat, cut them with wire cutters. I then spliced the matching wires together and attached the part to the coil tube (There is a little clip on the part, be sure to do this because I forgot and had to go back and do this again!!!).

i took out back frame and cleared off the ice on the metal condenser. I cut wires from old thermostat and removed it. Stripped new wires and attached to the wires in the frig. We taped it with electrical tape and put it back and closed it up. it works beautifully! We watched a video on youtube and that helped a great deal!

All the rest of everyone's post are all what I did. The only other thing I recommend is to put the back panel over the evaporator coils when your done. I replaced defrost thermostat, and heater. Once I initially completed it it kept icing over more than usual. You have to put the back panel back on so airflow goes over the coils.

My Ge top freezer fefrigerator was going into defrost mode and the heater was staying on for too long causing the food to thaw and eventually refreeze. Originally thought it was the mother board but after researching and do some troubleshooting of my own I realized the defrost terminating thermostat was bad. $8 part from Parts Select. Accessed the evaporator by removing back wall plate. Located thermostat and cut two lead wires to it. Spliced in new thermostat and reattached to eveaporator. Refrigerator seems to be good as new. There is an installation video on the web page that shows you step by step proceedure.

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

I followed instructions posted by experts and hands-on experienced owners on PARTS SELECT.Very helpful! Repairs was easy!.Defrost thermostat tried first,unsuccessfull then the DEFROST HEATER HARNESS next :BINGO !. Thank you PARTS SELECT ! Thank You every ones who posted their successful experiences that gave me confidence.From now on I know I can count on PARTS SELECT and its sites to solve my future headaches!

Replaced top sensor in ref. and top sensor in freezer as well as defrost thermostat - works as advertised - easy fix, saved a bundle thanks to this site! Parts ordered and shipped quickly and without complications!