CTS18HBSERWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- jim from CORNING, NY
- Parts Used:
- WR17X11662
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Plastic bracket broke so vegetable drawer would no longer stay in place
Pipes out the glass from existing shelf while in place inside refrigerator. Remove broken shelf. Install new shelf. Clean and replace glass. Easy job thanks to finding the correct part from Part Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from TUCKER, GA
- Parts Used:
- WR17X11890
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Missing shelf
Went right on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter M. from Lincoln Park, NJ
- Parts Used:
- WR02X10540
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Defroster fan burned up
First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacky from Richland, GA
- Parts Used:
- WR60X10207, WR60X10168
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Old fan motor was knocking and not running well
Watched your repair video online. appeared very simple and straight forward. Order the parts in question. They were shipped quickly. Once parts in hand watched video again and then installed new motor and blade in less than ten minutes. Plug power back in and and new part works perfectly. Thanks for helping make it an easy process. J. Smith
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Duryea, PA
- Parts Used:
- WR17X11889
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cracked shelf
took old one out replace new one less then minute
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jack from homestead, FL
- Parts Used:
- WR60X31522
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Fridge making LOUD humming sound.
Started removing screws until I got to the fan (it's easy). Then just took out the old fan and put the new one back in the same way. The only challenging part was putting the clamp back on the fan, but I finally got it. The fridge is finally quiet and we can sleep again! PartSelect made it really easy and they were incredibly fast. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jodi from Benton Harbor, MI
- Parts Used:
- WR23X37285
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light out
Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MaryLou from Levittown, NY
- Parts Used:
- WR60X10207
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Noise in the back of freezer
I must thank yo for sending the fan so fast. If I ever have to deal with any appliance again, you are first on my list.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paypal_shipping_address from Ripon, CA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Light would no longer turn on
I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from POCONO LAKE, PA
- Parts Used:
- WR60X10168, WR02X10098
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
the condenser fan motor was intermittently verynoisy. obvious sign of a (possibly imminent) failure
1 unplug the appliance
2. remove the rear cardboard cover, giving access to the compressor and condenser area
3. remove the two (condenser motor bracket) mounting screws, then with the motor assembly in your hand remove the the fan blade which is friction mounted to the motor shaft( note the exact position of the fan blade on the motor shaft so you can replace it in the same position when you reassemble), remove the two wires connected to the motor. Also remove the rubber resilient mounting grommets on the motor mount frame as these can harden with age and cause excessive vibration.
4 install the new motor into the mounting frame with the new grommets
5 reconnect the two wires to the new motor (non polarized)
6 secure the mounting frame (with the installed new motor) back in place
7 slide the fan blade onto the new motor shaft
8 screw the rear access panel back in place
plug in the refrigerator. the next time the compressor and condenser fan cycle on, verify operation of the new condenser fan motor
2. remove the rear cardboard cover, giving access to the compressor and condenser area
3. remove the two (condenser motor bracket) mounting screws, then with the motor assembly in your hand remove the the fan blade which is friction mounted to the motor shaft( note the exact position of the fan blade on the motor shaft so you can replace it in the same position when you reassemble), remove the two wires connected to the motor. Also remove the rubber resilient mounting grommets on the motor mount frame as these can harden with age and cause excessive vibration.
4 install the new motor into the mounting frame with the new grommets
5 reconnect the two wires to the new motor (non polarized)
6 secure the mounting frame (with the installed new motor) back in place
7 slide the fan blade onto the new motor shaft
8 screw the rear access panel back in place
plug in the refrigerator. the next time the compressor and condenser fan cycle on, verify operation of the new condenser fan motor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from MEBANE, NC
- Parts Used:
- WR60X10168
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Noisy Fan Motor
Simple. Rolled the refrigerator out , unplugged the 120 volts AC outlet.(1) Unplugged the wiring from the cabinet to the fan (white (three pin connector)). (2) Removed the two 5/16 inch screws holding the rear motor bracket . (3) Removed the fan blade from the motor shaft by applying slight pressure, pulling if off the old motor shaft. (4) removed the rubber isolator from the frame and from the rear of the old motor. (5) placed the rubber isolators back on the motor and frame. (6) Pushed the new motor back into the frame and re-installed the fan assembly. (7) remounted the fan with the rear support and the two 5/16 inch screws. Reconnected the three wire connector. Just checked the fan blade assembly to make sure they were not hitting the fan shroud. Fan blades should sit just partially inside the shroud to make sure it produces maximum airflow.
(8) Reconnected the 120 volt AC and waited for the compressor to cycle back on... Nice quite fan... Thanks
(8) Reconnected the 120 volt AC and waited for the compressor to cycle back on... Nice quite fan... Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnie from BATON ROUGE, LA
- Parts Used:
- WR82X10111
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
had no access cover on back
screwed the cover on just like the original
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from BROOKLYN, NY
- Parts Used:
- WR17X11889
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken door shelf
Slipped it it-very easy
Was this instruction helpful to you?
Thank you for voting!