TFZ20JRYDWW General Electric Refrigerator - Instructions

After reading the stories here, I purchased one door closing cam. After getting into the problem area, I realized I needed 2 cam, so I put the door back together and ordered another cam. If you have this problem, buy 2 cams.

I just followed the instructions on the video and it was exactly as they said......no surprises.

This one is a no brainer… One Phillips screw on top to pull top door hinge trim. Two nuts and the top hinge is free. Then pull the door… it helps if you unload all the crap in the door bins. Remove the remnants of the door cam and that leaves a pop rivet. Put some vise grips on the head and use a hacksaw to remove the lower part of the rivet. Then pop-rivet the new door cam in place. If you don’t own a pop-rivet tool, I guess you could use a 10/32” screw and nylock. Plop the door back on and you’re done. Took all of about 15 minutes.

I placed books under the door until I had enough to hold the door up about 1/2 inch higher then when it is closed. The books and the magnetic gasket will hold the door, JUST DON'T TRY TO OPEN IT TILL YOU'RE THROUGH. That's about how high the cams lift the door when opened. I removed the two screws holding the door stop. Then removed the two screws holding the lower hinge pin.

It takes two of the cams

and the bottom one is riveted to the hinge. I used a grinder to grind the rivet so I could tap the pin out holding the cam. Put the new cam on and put the pin back in. I didn't put a new rivet, just gravity should hold it. I put the second cam on the hinge pin and one of the screws on the door stop holds it in place after you slide the hinge pin back into the door and replace the screws in the bracket then the door stop.
Make sure your lower door gasket didn't get damaged while the cams weren't working because the door wasn't being lifted up when opened.

Same problems as already described .... door would not close, plastic bits on floor, angry, ready to throw-out 15 year old “dog” and blow at least $1,000 on a new appliance!

This repair is dead easy. Remove the two bolts holding the top hinge and lift off the entire door. Don’t be surprised if the original Riser Cam has virtually disintegrated, mine was a wreck. Remove two bolts that retain the old flat metal “shim” and fiber “gasket”.

Fit new Riser Cam and re-use old shim and gasket. Replace door on dome-shape bottom hinge mount and then re-fit top hinge.

If in any doubt order new shim and gasket along with the new cam riser. Or, do as I did, and “manufacture” either of these parts from scrap material found in the workshop ....

Like the rest of the other statements it was easy with 2 2X4 pieces of wood to block the door up. The other suggestion about buying two of the pieces was a good idea. Once I took off both the top and bottom pieces they were both worn out and it was easy to replace them both at the same time. The door is working good again and shuts on its own.

I blocked the door up with one 2X4 Then removed the lower hinge, installed the closing cam. Then I found that I needed one more closing cam that I didn't order the first time. This other one mounts to the lower section of the door and both cams set together. Re-ordered another cam. When it came in I installed it. Between ordering both parts I had them both in three days. The best to Parts Select
I now know where to buy my parts if needed again.

Thanks
Bob
Sandusky, Ohio

Removed four screws at bottom of door, while someone held the door in place replaced the upper cam (there are two) applied some silicone plumbers lube between the mating surfaces and tightened it up. Works like new bottom cam was only slightly worn. P.S. Remove everything from the door first.

There are Great videos on YouTube!!! Turned off power,Removed trim ring, Pushed a philips head screwdriver in one of the holes underneath the electrical panel with the selector push buttons. This releases the electrical panel. There are Three wire sets with plugs. I removed the plugs and took the electrical panel out. Removed four Phillips head screws and pulled out the big paddle switch. This then exposes the flapper. Replaced flapper with new one and reassembled everything. When I had everything apart, I cleaned with window cleaner. It was pretty moldy from the water leaking. Turned power back on and tested everything to make sure I didn't mess anything up. Works great

Researched on internet/you tube; ordered part, and did the repair. Easy to do and saved the cost of a service call.

unclipped and replace with new part.

Replace the flapper and this solved it. The video provided was excellent and allowed me to do this repair myself.

Turn off power
Remove operator faceplate by pullling out on outer lower corners
Disconnect wire connectors from circuit board
Remove four screws from dispenser and pull out dispenser assy
Replcae Door ASsembly
Put everything back in place
Power up
Job Done

Under the control panel there are three small holes. Insert ballpen or small flat screw driver on both outer holes to push a tab lock that holds the control panel in place. Then pull out control panel and three set of wires will be exposed and disconnect wire connectors (connectors have different sizes so you wont get confused in reconnecting). Unscrew four screws on each corner that holds the ice dispenser assembly (a part where you push your glass against to dispense ice or water. The flapper is exposed and easy to replace.

Excellent video was available on the Parts Select website. It was simple. The selector panel pulled out by hand from the bottom. The subpanel was removed with the four screws. The flapper snapped out of the holder with two clips. The new one was inserted in reverse order.