TFH22PRSBBB General Electric Refrigerator - Instructions

I took the top over off the pivet bracket and used a nut driver to remove the screws on the pivet. Lifted the door off and put on some saw horsess. I revoved the pieces of the old cam on the door by taking out the screw and put the new cam back.
I then drilled out the rivet on the bracket on the door and removed the broken cam. replaced it with the new one and used a screw and nut to replace the rivet. Put the door back and works great now.

i'm glad I read this forum before ordering the part because you need two of the door cams. They're sandwiched together on the lower hinge.

I removed the top door hinge, lifted the door off from the lower hinge and layed it on the counter.

I then removed the lower hinge using a nut driver.
I had to grind the rivot head off that holds the door cam onto the hinge and use a nut & bolt to replace
the rivot.

I Supported the door with wood blocks. Then used a socket wrench to remove both parts of the lower hinge. I had purchased 2 of these plastic closers as recommended. One of them must be cut off with a Dremel Tool or small grinder. A small bolt and nut replaces the rivet that was cut off. Reinstall it just as it was removed. Job complete.
Parts were delivered on time, web site instructions were excellent. I highly recommend PartSelect.com

The old plastic door closer cam on bottom of the the door had broken. What was left of it was held on by a hex head screw. There was also a fiber spacer under the cam that was broken. I made a new one out of a piece of aluminum, but cardboard probably would have worked.

Forgot to mention you have to take the door off first--loosen the two screws on the top hinge and lift the door out of the bottom hinge.

I found the self-closing sometimes won't work well until there is some weight in the door.

Followed previous poster's steps. Replacement of door closing cams took 35 minutes. Make sure you buy 2 cams for each door.

completely removed door, then replaced worn-out cam on bottom of door-simple enough; then removed hinge from bottom of refrigerator; removing old cam required drilling out the rivet that fastened cam to hinge; secured new cam to hinge with small machine screw and nut. This procedure is relatively easy but does require minor mechanical ability and having a small drill and bit set. However, replacing the two cams totally fixed the problem.

I did not realize I needed 2 cams to complete repair. Door cam was riveted in. I had to drill out rivet and replace with nut and bolt. Otherwise it went quite sommothly. At first I just replaced the cam on bottom of refridgerator but door was not quite right when closing. Further inspection showed the door had the other half of cam that also needed replacement. Needed 2 orders. Paid for 2 shippings.

Followed the instructions and replaced the door recess.

took off the panel, took out 4 screwws, took out old flap, installed new flap, put screws back in , and put trim back on.

Your vidio was Brilliant !!i just followed your instructions

Took the door contents out and put them on the counter, took the door off the hinges by unscrewing the 2 screws on the top of the Fridge and lifting the door off the hinge onthe bottom. Then laid down the Fridge on the kitchen floor and replaced the Door Closing Cam, keeping in mind the order of the 3 shims and other things on the bottom of the door. Simple.

This my second time to do it after 8 years. Took 10 minutes.
1 Remove all the contents on the side door
2 Remove the 2 bolts on top connecting the door to the refrigarator
3 Lift and remove the door up and put it the side
4 Clean and remove the old door closing cam put the new one
5 Door ref is fixed

Replaced both upper and lower cam's. Removed door from refrigerator, removed bolts on door cam on bottom of main door and replaced cam, then removed bolts from door hinge assembly, drilled out rivet holding on cam, replaced with new cam and re-riveted.

1st: Order (2) closing cams! One for the hinge pin / bracket and one for the bottom of the door.
The closing cam on the door was where the Dremel type tool is required, since you have to grind the head off of a factory rivet.
I installed the cam with an aluminum pop rivet.
Next, remove the bracket on the bottom of the door with sockets and install the second closing cam.
Re-attach the top door hinge pin and align visually; tighen all bolts. Job finished, but more important , my wife is not nagging me about the repair that I put off for over a year!!!!

Removed the top cover using a Phillips screw driver to access the top 2 screws holding the bracket. Once the bracket was removed, lifted the door off the bottom hinge. Replaced the door closing cam, replaced shims and screws. Placed the door back on the bottom hinge, inserted the top bracket and secured.
This was the ultimate resolution to the problem. The problem I encountered was getting all of the correct parts. It took me 3 tries to finally identify and receive the parts needed to make the repairs. Using Part Select made it easy because they had the parts I needed. My 3 tries were partly my error and does not reflect on Part Select. I would recommend others use Part Select when choosing their replacement parts.