TFX20RLD General Electric Refrigerator - Instructions

Ordered at PartSelect and received the auger and blade within days. Printed the parts diagram and proceeded to take the auger apart the time it took would have been much less but I seized the opportunity to do a deep cleaning of the old parts before replacing them....The part diagram was the key to simplicity and the fast shipping was awesome. Thanks I'll be back....

This one is a no brainer… One Phillips screw on top to pull top door hinge trim. Two nuts and the top hinge is free. Then pull the door… it helps if you unload all the crap in the door bins. Remove the remnants of the door cam and that leaves a pop rivet. Put some vise grips on the head and use a hacksaw to remove the lower part of the rivet. Then pop-rivet the new door cam in place. If you don’t own a pop-rivet tool, I guess you could use a 10/32” screw and nylock. Plop the door back on and you’re done. Took all of about 15 minutes.

Read the how to's AFTER ordering the part. 2 things....1) I wish I had read the comments first and 2) it was much easier than the comments led me to believe.

Had I read the comments first, I would have known to order BOTH the upper and lower cam....though there not a problem with the operation of the door. It would just have been a tad better if I had both. I'm not wanting to have to pay shipping for an additional part when the door works satisfactorily as it is.

As to the comments on how to do it....I took none of them. I (instead) removed the top hinge, and lifted to door off. I did have to have assistance to get the hole in the door aligned with the post, but that was rather easily done.

Would I do it again.....in a heart beat. I feel that I've save on the repair man making a call at the house, and experience has had me charged $60-$100 for virtually the same amount of service. My cost...shipping and all was under $20.00

Removed the top hinge cover held by one screw. Removed the top hinge held by two screws and them lifted the door up and off the bottom hinge. Laid the door on the floor and replaced the cam piece from the kit on the bottome of the door. That required removing one screw and losening another. Removed the lower hinge (two screws) and replaced it with the new one in the kit. The lower hinge includes the other cam piece. Lifted the door onto the lower hinge and then replaced the top hinge and cover.

I was set to buy a new magnetic seal to hold the door closed, when I looked it up on PartSelect I saw the recommendation that the problem might be the door closing cam.. I check it with a mirror and sure enough the cam had broken and the door sagged about 1/4 inch. I then followed the instruction and removed the top hinge, lifted the door off and replaced the cam. I did need two and the one attached to the lower hinge had to be drilled out and a new screw and nut attached to hold the cam. It was simple to do, I would recommend selling the door closing cam be sold in pairs with a #10 1/2 inch long screw with lock nut.

After reading the stories here, I purchased one door closing cam. After getting into the problem area, I realized I needed 2 cam, so I put the door back together and ordered another cam. If you have this problem, buy 2 cams.

First, I was glad I read other posts on this repair as I would have only purchased one of the replacement cams when I needed two! I removed the top door hinge with a screw driver (cover) and small socket set for the door hinge. I then removed the door and removed the bottom hinge (socket set). The bottom hinge had a small rivit that held the bottom cam in place. I used a hack saw to cut off the rivit and replace the cam and secured it with a small machine bolt and nut. I then laid the door on its side and removed the top am from a bracket attached to the bottom of the door. I relaced the cam (second one) and reinserted the screws. I reattached the bottom hinge and then placed the door on the bottom hinge pin. I then held the door in place while inserting the top hinge pin bracket into place and retightening the top screws. I replace the cover with a screw drive which was the ahrdest part in trying to find the hole the small screw gets inserted into. DONE!

Like the rest of the other statements it was easy with 2 2X4 pieces of wood to block the door up. The other suggestion about buying two of the pieces was a good idea. Once I took off both the top and bottom pieces they were both worn out and it was easy to replace them both at the same time. The door is working good again and shuts on its own.

First i removed the lower cover below doors . Then placed a 4x4 under the door to be fixed to keep it in place. Removed screws from hinge support on unit to remove cam Removed outside screw on door and loosened other to allow other cam to be removed . Always buy two cams if one is broken the other cant be in very good shape .The door will work like new with two .

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

First a big thank you to PartSelect.com. I read the stories posted by others before ordering the parts and found out that I probably needed 2 of these cams. So I followed the advice of others and ordered 2 cams. I'm really glad I did because once I got the door off I discovered both were broken up real bad. Maybe you guys should think about offering them as a set?
Anyway the repair was fairly easy, except for the bottom cam which was revited to the bottom bracket. Again, thanks to the other stories about repairs with this part I was already expecting this. So the repair went like this. I removed the door by unscrewing the hinge on top(1 screw and 2 bolts). Took the door off and laid it on its side. Removed the bottom bracket( 2 bolts). Used a drill to drill out the rivit. Used a spare screw/nut that I had in a tool box to fasten the cam to the bracket. Put it all back together and I was done. The biggest challenge was figuring our if I needed 2 cams,so with the advice of others on your site, my repair was a snap.

Removed four screws at bottom of door, while someone held the door in place replaced the upper cam (there are two) applied some silicone plumbers lube between the mating surfaces and tightened it up. Works like new bottom cam was only slightly worn. P.S. Remove everything from the door first.

The plastic door closing cams had broken after 17 years of use. It was tricky figuring out how the new cams fit as the old ones had disintegrated. Also you need 2 cams - not one. I first ordered only one. A detailed parts diagram would have helped. First unscrew the top door mount cover and then the top door mount. The fridge door then lifts up and off the lower door mount. Next is the hardest part - drilling off the old pop rivet which held the lower cam. The lower door mount had to be removed to get at the underneath of the pop rivet, and a bench vise was handy to hold it as I drilled off the old rivet. Then you need small stainless steel nut and bolt and split washer or lock nut to replace the rivet. Next unscrew the old upper cam from the underneath of the fridge door and replace. The large hole in the cam goes through the door hinge pins. The two plastic cams should interlock in a way that makes the door swing close. Anyway, now the door works fine.

At first, I noticed the refrigerator door didn't close at the same level of the freezer door. I started to adjust the hinges and noticed a chewed up black 'washer' at the base of the door hinge. Ppartselect.com was awesome, in that I easily found the schematic of my fridge, and the part I needed. Ordering was a snap, and it came to the house pretty quickly.
Installation, first raise the door up as high as you can, then scotch it with wood blocks (closed door). This takes the pressure off the bottom hinge you must remove.
Taking the hinge off is a snap, but then the problem presented itself. The old door closing cam was riveted to the hinge. I couldn’t get the old one off! I ended up taking it to the garage and breaking out the Dremmel tool with the abrasive cutter (the one that will cut through nails. I ended up cutting off the rivet. This was a pain.
I then found a small nut/bolt and put the new piece on, then put it back into place and removed the blocks. Works good as new. The toughest part by far was getting the old cam off… but there may be some easier way to get the rivet out that I’m not aware of.
Good luck.

took top bracket off--then removed door--took
bottom bracket off bottom of door and replaced
door closing cam and reasembled---a piece of
cake