TBX22PRYPLAA General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robin from Georgetown, TX
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Our icemaker quit working.
My husband took the old icemaker out before the new one came in. When the new one arrived, I installed it in less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark J. from Alice, TX
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker quit working, I took it apart and found a broken wire at the thermostat, soldered it back, but apparently it got too hot.
It took longer to remove the ice bucket and frozen food than it did to replace the ice maker. Remove one screw with a 1/4" nut driver, slide outward and remove plug. transfer water tube to new unit. plug it in, slide into rear slots and install one screw. Replace ice bucket and frozen food, shut the door and hear ice falling in about 30 min. Easy job! Great product! THANKS MJS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HERBERT from Harlingen, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
gasket was shot
took off the panel, took out 4 screwws, took out old flap, installed new flap, put screws back in , and put trim back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from zion grove, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rubbeer flapper was worped causing frost in the freeze
The same as the vidio, very easy. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Atlanta, GA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost was building up inside the freezer just above the ice dispenser shute.
Followed the instructions and replaced the door recess.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Arlington Heights, IL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost on the bottom of the ice bin frome warped rubber flapper
Pulled the outter cover off, removed the electronic board, replaced the flapper and put it back together again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ade from oceanside, CA
- Parts Used:
- WR17X2770
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The slide rail for the vegetable drawer broke in a refrigerator that is at least 15 years old.
Removed the broken rail (2 screws), replaced the new rail (2 screws), reassembled all in about 8 minutes. It was AWESOME!!! I had spent hours trying to repair it and, fortunately, gave up and decided to look online for the part. Didn't even think that the part would still be available. Not only was it available but it arrived in 2 days! Anything that is broken in the future: I am going to your website first! Thank you!!!
Was this instruction helpful to you?
Thank you for voting!
broken vegie bin slide rails
This was very easy. Just unscrew the broken side pieces and attach the new ones. If the rubber gaskets are still in good shape, gently pull them off and attach them to the new rails. I was very impressed with the service from Partselect.com. I gave them my appliance model number and they helped me find the right part. I ordered on Sunday evening and had the parts in hand by Tuesday. Great service! I will definitely use this company if I need more parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Prospect, CT
- Parts Used:
- WR17X2769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the side rail broke because I kicked it
I took out all the stuff on the shelf, and the drawers.
then I took out the shelf, pulled off the cover so I could get at the screws.
I unscrewed 2 screws, threw out the old part, and screwed the new one into the shelf.
then I put the whole thing back together, in total the hardest part was cleaning off the shelves and then putting everything back in.
As a note, there was a gasket on the old rail that was not on this one. I had some silicone tabs that I used instead, but I really think the gasket should have been part of the order.
then I took out the shelf, pulled off the cover so I could get at the screws.
I unscrewed 2 screws, threw out the old part, and screwed the new one into the shelf.
then I put the whole thing back together, in total the hardest part was cleaning off the shelves and then putting everything back in.
As a note, there was a gasket on the old rail that was not on this one. I had some silicone tabs that I used instead, but I really think the gasket should have been part of the order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Davis, CA
- Parts Used:
- WR17X2769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The support for the vegetable drawer cracked
The repair was very simple. The longest part was taking everything off the shelf in the refrigerator so that the slide rail could be removed. Then when things were out, it was clear that the bottom of the refrigerator needed cleaning. The repair itself was done quickly. The cleaning (yuck) took longer! this is a great site because the part came quickly and it was very easy to select just what was needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Raleigh, NC
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Icemaker stopped cycling and wouldn't make ice
I removed the lower screw (not needed for the new icemaker), loosened the 2 top screws, unplugged the wire harness and removed the old icemaker. Unpacked the new icemaker assembly from the box, wiped the ice cube depressions to remove any debris, snapped on the water tube adapter, hung the new assembly on the 2 loosened upper screws and tightened the screws. The wire harness required the supplied pigtail plug which made the wire assembly long and awkward to replace the ice bucket/dispenser assembly, plugged it in and was done. It took a total of about 10 minutes for the entire operation and had a full bin of ice cubes within 36 hours and was ready for the ice dispenser/crusher in the freezer door. Easy install!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shelli from gaithersburg, MD
- Parts Used:
- WR17X2770
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
slider cracked, so drawers wouldn't stay in
The entire frame that holds the two crisper drawers pulls right out. After that, it's just a matter of unscrewing the broken part, snapping in and screwing the new part and sliding the whole thing back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Darien, CT
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker stopped working; would not fill
It was as easy as the instructions were clear (and they were). Remove 2 screws and two nuts, pop out the old ice maker, pop in the new, plug in and tighten screws/bolts. It worked. I'm happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Max from Corvallis, OR
- Parts Used:
- WR17X2769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The Slide Rail was broken
First i removed the vegetable drawers and slide rails. Removed two screws from the old rail then replaced it with the new one. Then replaced the vegetable drawers. It was that simple. The replaceement part was delivered to my home in threre days after i ordered it on line. It was better than going to a dealer and having them order one for me then having to make another trip to pick it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Pittstown, NJ
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice chute from the ice maker frosted over. Cubes would not dispense
1. Unplug the fridge
2. Removed the outer facing of the dispenser outside the freezer door. This is fairly easy, better with a tool (plastic scraper) that won't mar the finish.
3. Removed the plastic plate with labels -- water, ice, etc. This is done by sliding a small jewelers screwdriver into the slots on the left, middle and right in back of the plate. These are difficult to see without a flashlight.
4. Removed the four screws in the panel behind this plate.
5. Unpluged the large cable on the left side after the panel is freed.
5. Removed the rubber "dispenser" button. this just pulls off.
6. Remove the panel
7. Lift flapper up and remove. Clips hold this in.
8. Put new flapper in place.
9. Use reverse order to put back together.
Piece of cake. Ice maker no longer frosts up.!!!!
2. Removed the outer facing of the dispenser outside the freezer door. This is fairly easy, better with a tool (plastic scraper) that won't mar the finish.
3. Removed the plastic plate with labels -- water, ice, etc. This is done by sliding a small jewelers screwdriver into the slots on the left, middle and right in back of the plate. These are difficult to see without a flashlight.
4. Removed the four screws in the panel behind this plate.
5. Unpluged the large cable on the left side after the panel is freed.
5. Removed the rubber "dispenser" button. this just pulls off.
6. Remove the panel
7. Lift flapper up and remove. Clips hold this in.
8. Put new flapper in place.
9. Use reverse order to put back together.
Piece of cake. Ice maker no longer frosts up.!!!!
Was this instruction helpful to you?
Thank you for voting!