GSG25MIPHFWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Melvin from Duffield, VA
- Parts Used:
- WR30X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
It was the crusher dispenser cover, not the bucket. Anyway, it was broken
used a phillips screw driver to remove two screws that held
the crusher assembly on the end of the ice bucket. Then I used the flat blade screw driver to pry the slot locks open and removed the dispenser cover. reassembly was areverse process.
the crusher assembly on the end of the ice bucket. Then I used the flat blade screw driver to pry the slot locks open and removed the dispenser cover. reassembly was areverse process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bert from Audubon, PA
- Parts Used:
- WR60X30922, WR02X12149, WR02X11331, WR02X10322
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
High pitch noise
My GE refrigerator emitted high pitch noise a short while ago. I tried different dampening methods that helped but not eliminating the problem. I finally replaced the fan, motor, and associated parts and solved the problem. The total cost was about $50.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Virginia Beach, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Flapper was stuck open. Old and warped.
Replaced flapper
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Manchester, NH
- Parts Used:
- WR02X11330
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Moving the refrigerator into my new (very old) house we had to remove the doors which resulted in a crimped hose and union
Remove lower front panel, disconnect damaged union from water hose under freezer door, replace with new union, tighten and reattach front panel. No more water coming from under the unit. Ice maker and dispenser features returned to working order!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- roy from spring hill, KS
- Parts Used:
- WR02X10552
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
going from warm to to cold
i used the video it showed on the site or iwould not have been able to do it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from west bend, WI
- Parts Used:
- WR17X11170, WR49X10233
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The unit will not dispense water, but does make and dispence ice.
I replaced that part, but I still have the same problem, no water is dispensed. I believe I may need a circuit board. The problem was not the parts I replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Georgetown, TX
- Parts Used:
- WR17X23255
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The auger in ice maker was broken and not delivering ice through dispenser.
Replaced entire ice bucket and auger assembly (one piece).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Huntersville, NC
- Parts Used:
- WR71X38317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken dairy door
Part arrived in 2 days and took about 15 seconds to install. Great!! No more broken eggs!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael D. from Boiling Springs, PA
- Parts Used:
- WR29X43990
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Augur blade broken
Ice maker assembly removed from refrigerator and disassembled. Note nylon nut holding the Augur in place is removed clockwise. As you take the assembly apart, note each piece for reassembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from Loganville, GA
- Parts Used:
- WR17X11497
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Cover was cracked affecting ice dispensation
Removed the ice tray and then the auger unit from the tray assembly. To accomplish auger removal, the auger assembly is attached to the tray assemble at the front. On the front bottom there two screws. Back them out. Then on the top of the tray assembly the auger assembly is held in position by two tabs. Depress them with a finger or thumb. Do not use a screw driver as this may result in breaking the plastic tab! The auger assembly will separate. The crusher plate easily separates from the auger assembly and is removed buy "spiraling" the plate up and off the auger itself. Simply reverse to install new plate.
Recommendation: Take this opportunity to thoroughly clean and COMPLETELY DRY all components prior to re-assemble and re-install into the refrigerator.
Recommendation: Take this opportunity to thoroughly clean and COMPLETELY DRY all components prior to re-assemble and re-install into the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lou from Tampa, FL
- Parts Used:
- WR29X43990
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the auger that dispenses the ice broke
I downloaded a schematic of the ice dispensing unit. The whole unit pulls out and there are a couple of screws that remove plastic covers. The "trick" was to get the two plastic tabs pushed in and lift the auger unit out of the tray - a two person job! We used knife blades (it was the thinist and strongest tool around) to push the tabs in and pry the auger assembly out. I think we did a great job NOT breaking the plastic pieces! As careful as I was, I definately needed the schematic to put the ice crushing blades and spacers back together. All of this could be avoided if they used a metal auger instead of plastic!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Somers Point, NJ
- Parts Used:
- WR23X10725
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switchlight was broken on tennant's refridge
as described, I used a thin screwdriver to wedge in and pull down existing, broken switch. I was able to pull it down about a 1/4 inch, but wasn't quit able to disegage it until I gripped it with pliers. I then pulled it out, unplugged the old switch, plugged in the new switch, and carefully tucked the wires back into the fridge and snapped the new switch into place.
10 minutes total.
10 minutes total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patsy from Jal, NM
- Parts Used:
- WR29X43990
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
replace auger in the ice maker
We had a little difficulty getting the washer back on properly because my husband could not remember how he took them off. I finally got the parts in front of my computer and brought up the picture of the auger and parts that showed me how to put the washer back properly and we got it back together and it works fine. Not bad for two old people I am 80 and my husband is 79 but we still take pretty good care of things.it would have been a little easier if I could have printed the picture off, but we made it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merlin from Dawsonville, GA
- Parts Used:
- WR29X43990
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken Augar
I am 85 years old and had no trouble replacing the Augar. Removed ice maker from frig. Remover the ice shield (one screw, remove front panel (2 screws) carefully removed augar assy.
Removed the lock washer,the the end plastic nut, being careful in removing the ice crusher blades. Replaced the augar and all parts. Checked out the ice dispenser and the crusher, both worked fine
Removed the lock washer,the the end plastic nut, being careful in removing the ice crusher blades. Replaced the augar and all parts. Checked out the ice dispenser and the crusher, both worked fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Graeme from Sarasota, FL
- Parts Used:
- WR62X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Icemaker flap not closing, frosting up
Watched video, however could not get outer casing off. Under the panel are three small holes, pushed up with an Allen key, used a small screwdriver to wedge out, came out easily, followed instructions from video on removing and replacing solenoid
Was this instruction helpful to you?
Thank you for voting!