ZISS42NCBSS General Electric Refrigerator - Instructions

simple - removed the cardboard cover plate at base of refrigerator back - removed existing water valve assembly - removed water lines from existing valve and plugged into new valve - same done with electrical connections - no tools needed for this part - re-attached valve bracket to refrigerator and closed her up - voila, water worked - probably spent 1/4 of that if repair guy had come out. sj

TURN WATER OFF TO REFRIDGE. TURN OFF ELECTRICITY.

Remove old ice maker (AFTER REMOVING THE BIG ICE TRAY) by disengaging two philips head screws but don't totally unscrew them. You must then totaly unscrew the bottom screw below the top two screws. Unplug the 5 head connection. (electricity)

Use adapter for the electrcity, etc from the box, (five head connection) Use the old plastic hose to hit the new cup. TIGHTEN TOP SREWS. LEVEL BY EYE. Turn the system on. Prime with some fresh water.

PS make sure that the light is on (green) and you will be in ice city. Be careful not to disengage the elcectic head when replacing the big ice tray.

HAVE A COCKTAIL!

Removed old Ice maker and replaced with new Ice maker.

I removed the screws that held the unit in place, and also the screws that held a plate that covered where the unit plugs in. I unplugged the unit, and removed it. Put the new one in, reversing the steps. Turned the new unit on, and had ice in 45 minutes! Summer is coming, I need my ice maker! This is the second unit I have replaced on this refrigerator, the first one was not releasing the cubes. This second one was a different style than the first, but same install process.

I'm so glad I didn't have to call a repair man to come in and fixed this. I probably saved myself a couple hundred bucks. Fixing this was really easy. Make sure you unplug the fridge and turn off the water first. There is only one screw on the bottom right of the fridge that secures it to the box. On my fridge I needed a socket set to remove it. Once that is removed the entire water valve can be pulled out. Unplug the wiring harness from the old valve and put it on the new one. I did the water hoses one at a time. Unplug one from the old valve and plug into the new. . I think there are 4. The main water hose you need a wrench to loosen but its the same principle. After that turn on the water and inspect it for leaks. Then reattach it to the fridge with the one screw. Hope this helps.

Disconnect power cord and turn off water suppy - removed access cover - remove assy from unit - inverted valve assy and connected water lines in new assy - re-installed valve assy - re-powered and turned on water - monitor for leaks 10-15min
done deed...

My husband took the old icemaker out before the new one came in. When the new one arrived, I installed it in less than 10 minutes.

Loosened 2 screws unplugged cable. Plugged in cable adapter on new unit. Plugged in to receptical, hung on 2 screws, tightened 2 screws. Done

It took longer to remove the ice bucket and frozen food than it did to replace the ice maker. Remove one screw with a 1/4" nut driver, slide outward and remove plug. transfer water tube to new unit. plug it in, slide into rear slots and install one screw. Replace ice bucket and frozen food, shut the door and hear ice falling in about 30 min. Easy job! Great product! THANKS MJS

Removed the Ice maker from the freezer because the light was not on. Disassembled ice maker, found printed circuit board had shorted across two posts because the board was black in that area. Bought new ice maker assembly, installed in less than five minutes, making Ice fine.

I removed the ice tub. Removed the screw on the left side that holds closed the section where the icemaker plug is connected. Disconnected the plug. Then removed the bottom right screw. I was then able to remove the Icemaker by unhooking it from the bcak freeze wall. I disconnected the icemaker from the fan gaurd. Removed the icemaker cover. unscrewed the 3 icemaker screws and opened up the chamber. removed the old Ejector Blade Drive Cam by removing the outer srew that hold the gear to the icemaker. changed the cam with the new one and reassembled everything.

I pulled the unit out, removed the lower access panel in the back. The receiving unit of the water line (Water Valve Assembly), had water spraying out of it which appeared to be as fine as a stran of hair. Aside from the wire attachments and multiple hoses attached to it, it was really easy to remove the old one and install the new one. Although the replacement part cost approx. $92, I would suspect I saved at least $50-$100 for a service call, not to mention who knows, $50-$100 in labor as well. Words of advice: Never be afraid to take on a challenge!

removed old ice maker, obtained part number from it. went on line ordered new ice maker at 10:45 in the morning, at 3:00 the nexte after noon new icemaker was in hand. took about 5 minutes to install new ice maker. works perfect. would do business again with this company.

Removed the drawer, took off the broken front, replaced with new part using same hardware and popped the drawer back in. Remember which is the bottom. The glass window is at the bottom. Was a simple job. Part was a perfect fit!

Removed old ice maker and control valve. Control valve is in the back of the refrigerator in the bottom corner. Unplug the refridge, turn off water supply valve, remove mounting screw and unplug the control valve from the wiring harness connection. Using a flat screw driver, remove the four water lines (this is the most difficult part). Go inside the freezer and remove the ice maker by loosening the two top screws and removing the bottom screw. Unplug the electrical connection by pulling straight out or use a flat screw driver to pry off. Installation of the new parts is the reverse of the removal. The new ice maker has a pig tail that is necessary to use. This pig tail is longer than the original but will loop up behind the unit and back down to the female plug. Full ice bucket in 48 hours.