TFT22JABBWW General Electric Refrigerator - Instructions

I watched the video on your web site first.Then I proceeded to do the repair exactly as the video showed. Very easy!!!!!

Turned refrigerator off. Removed food from right hand (refig.) door. Closed door. Removed upper hinge cover with a standard Phillips screwdriver and then removed upper hinge by removing two 5/16" bolts using nutdriver. Lifted door up to clear the bottom hinge-post and set it on the table. Removed the kick pan at the bottom of the refrigerator and then removed the bottom hinge-post which was attached with two more 5/16" bolts. Installed new lower hinge post and rubbed a small amount of mineral oil on the closing cam (which is riveted to the hinge-post). Removed the old upper closing cam from the door (5/16" bolts) while it as lying horizontal on the table and installed new cam lubricated with a small amount of mineral oil. dropped the door in place, replaced upper hinge and cover. Replaced kick pan. Done.

Use several wood blocks and propped fridge dooe up and someone else steadied the door while I replaced the hinge. Pretty easy.

This is a side-by-side unit. After blocking up the closed refrigerator door to the correct height to match the freezer door, I removed the lower hinge pin assembly by taking out two bolts. Save the shims (my had two) for the new hinge pin. Then remove the cam riser from the bottom of the door by taking out two bolts. Install the new cam riser on the bottom on the door. Then install the new hinge pin assembly. Total time 15 minutes.

blocked up refrigerator door.removed old hinge, and put new one on,with socket set.

Removed top hinge assembly to pull door away from bottom hinge (2x hex bolts) Discovered that the pin on the bottom assembly had broken off. Removed and replaced bottom hinge assembly (2x hex bolts). Aligned door with top and bottom hinge pins. Tightened all hex bolts. Done

I followed the many post on replacing this part and everything went well. I had a little trouble getting the hinge post into the new hinge assembly, but with a slight adjustment it fell into place. I checked to see what tools I would need to do the job and had them ready before I even started. I removed the door and had it back on in maybe 10 minutes and I am not exactly Mr. Fix It. The only advice I can add to what everyone else has said is you should look the job over a little before you take the door off and have your tools ready. Then you won't have the door off for too long. I'd like to thank this site and everyone who gave advice on how to fix this problem. It made the whole job very easy.

I can not find the bill therefore I do not know what part I installed, as I keep installing parts in my home. I believe you are referring to a Vegetable Bin of my GE Refrigerator and you do not have to be a rocket scientist to install a new one.

Sorry
Abraham Zighelboim
PS: I just saw that was the Veg Bean

It was really easy for me....my son told me what part I needed. I ordered it, and he installed it!

I removed all the items off the shelves of the door. I then removed the top assembly,Then lifted the door off the the bottom hinge and laid it on a flat surface. I then removed and replaced the cam connector on the bottom of the door. I then removed and replaced the cam from the lower right side of the refrigerator. I put the door on the cam without assistance , then reassembled the top assembly. The refrigerator door operated immediately just like it did when it was new over 20 years ago.

Several months ago I had to replace the hinge and cam on the refrigerator door and the repair went smoothly as pictured in the video. This time I had to replace the cam on the freezer door so I ordered the hinge assembly, which included the cam. The web site confirmed that, according to the model number of my 27 year old refrigerator, the hinge assembly would fit. The problem I had was that the top hole in the hinge was positioned too high to fit the hole in the refrigerator so I had to put the old hinge back on, even though it showed some wear. The door closes smoothly by itself now.

I just followed the video instruction supplied by PartSelect and the whole thing was a breeze.

Removed freezer door, put a blanket over the opening to keep food frozen. Installed hinge and replaced door.

Removal was easy. The problem was that the old hinge had screws approximately 3/4 inch apart. The new hinge assembly had screws 1 inch apart. The threaded backing plate matched the 3/4 inch spaced old hinge but would not line up with the new one. There was a hole in the refrigerator frame but no way to hold the screw from the back. I had to fine a bolt and nut that would fir and still be heavy enough to hold the weight of the door. This repair took place at my cabin--miles from any hardware store. I found a long enough bolt and nut but it was a little too big for the hole in the hinge. I had to drill the hole in the hinge out so it would fit. Trying to reach the back of the bolt with a nut was a problem. I used tape wrapped backwards on my finger to hold the nut and then reached around to start the bolt into the nut. It too a few tries but I finally got it. Bottom screw was not a problem. It took about an hour and a half to fix the door but it works fine now.

This is a side by side freezer/refrigerator, nearly 30 years old. The repair was very quick and easy. 1. Remove two screws from top bracket. There is no cover for the top hinge on this older model. (2) Lift off door and set on kitchen table. (3) Remove two screws holding bottom door hinge. (4) remove two screws hold the cam and shims on the bottom of the door. (5) replace the broken cam on the door, and the bottom hinge assembly. (6) Replace the door on the bottom hinge. (7) Re-attach the top hinge screws, making sure the door is parallel to the freezer door. It took about 10 minutes to do all of the above. Best yet, I ordered the kit about 10am on a Monday, and the parts arrived, normal delivery, before noon the next day.PS- I used petroleum jelly to grease the hinge before replacing the door. The only tool I needed was a nutdriver.