TFG22PRTCWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bobby from Danville, VA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
door dropped down and draging, would not close
Buy ( 2 ) cams !!!! removed hinge cover and hinge on top of the door, ( 2 screws )...lift door off of the bottom hinge and lay door on the floor, remove broken cam on bottom of door with nut driver, ( 2 screws ) , install new cam..... remove the bottom hinge off of the front of the refrigerator with nut driver, (2 screws ).... saw rivit off and remove old cam, install new cam and secure with new bolt and nut,... reinstall hinge back on bottom front of refigerator.....replace door back onto the bottom hinge.....install top hinge back onto the top of the door....replace hinge cover......done !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Naples, FL
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Fridge door was not self-closing
Followed step-by-step instructions in previous post. Note that there are TWO approaches, both of which work.
Option 1) Order TWO cams (PS297995), drill out the rivet holding the frame's cam, and replace it with a nut and bolt. (See post on 07/19/09.)
Option 2) Order the entire hinge assembly (PS290199), which includes the door's cam and an assembled frame hinge and cam. (See post on 10/29/08.)
We opted for Option 1 which was pretty easy. Option 2 would be even easier and take less time but costs about $9 more.
Thanks to previous posters for excellent instructions!
Option 1) Order TWO cams (PS297995), drill out the rivet holding the frame's cam, and replace it with a nut and bolt. (See post on 07/19/09.)
Option 2) Order the entire hinge assembly (PS290199), which includes the door's cam and an assembled frame hinge and cam. (See post on 10/29/08.)
We opted for Option 1 which was pretty easy. Option 2 would be even easier and take less time but costs about $9 more.
Thanks to previous posters for excellent instructions!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Franklin, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door recess asm would not seal tightly
remove the 'pop-out " frame around the door recess, you pry the flexable seal from around the ice despenser, have someone hold the unit with the wiring, remove the one screw that holds the door recess, and replace the new one. reverse the procedure. remember to unplug thr frig. first
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- phyllis from owensville, MO
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Old Cam Had Deteriorated, And Was Breaking Into Pieces And Falling Off.
We taped the door with 3 pieces of duct tape, then put boards under it. Used socket set to remove cam and then cut off rivet so we could just use a screw to keep in place. . . Just for your information, I ordered 2 cams, and was glad I did as I need 2 to make the repair. . . Didn't read about this online or on order recommendation. The cams go 1 up and 1 down thanks for the installation repair stories, it inspired us to "do it ourselves " and we saved about $75 to $100. 00
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Corpus Christi, TX
- Parts Used:
- WR49X10183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Rust in ice
Replaced auger and front helix kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jon from social circle, GA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
frost formed because the ice damper let warm air into the freezer
Removed frame, unscrewed the electrical panel, and popped the flapper off. Installed new flapper. Replaced the electrical panel and re-installed the frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Ocean View, DE
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door flapper to ice needed to be changed
Repair went exactly like the video. With this video it was easy to make the repair. There were no surprises or problems and I felt confident in the videos instructions. It was like pushing the easy button.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Dumfries, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper valve allowing frost/ice to accumulate in chute in summer
Followed the online video exactly and it was easily done. Couldn't have been better. The problem is solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from Toledo, OH
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Freezer door would not close properly
Using the #2 Phillips screwdriver I removed the top hinge cover from the top of the freezer door. Next I used the 5/16 nut driver to remove the 2 bolts holding the top hinge in place. Once it was removed I was able to lift the door off the bottom hinge. Placing the door on a flat work surface I loosened the bottom bolt holding the cam in place. I next removed the bolt holding the hinge in place. I was then able to remove the broken cam and replace it with the new one. I then replaced the bottom bolt making sure the hole for the cam and the hole for the hinge are lined up. I then tightened the bottom hinge bolts. I carefully placed the door back on the bottom hinge and put the top hinge back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Fripp island, SC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
3rd Flap for this Ice Mkaer, keeps warping
Very Easy, follow direction I the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Hughesville, MD
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
ice dispenser chute kept freezing with condensation
The flapper on the ice chute was curled up and not creating a good seat, so the chute kept clogging up with frozen condensation, especially during the humid summer months. The online video made it so easy to replace the part myself. I was able to fix the problem in under 15 minutes and at a fraction of the price!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Chester Springs, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper was warpped
Follow instruction on the video you provided
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from RIO RANCHO, NM
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Fridge cam broke, door barely closed and crooked
I followed your terrific video. I first got all tools ready, covered a table in cardboard, and removed food from the fridge door. I removed the cap and screws on top of the door hinge. Lifting the door off was simple, and after laying the door on the table, the retaining screw was easily loosened, and the cam screw removed. The only problem was that half the thin gasket under the broken cam was missing. No new gasket came with the part. I wanted the new cam to lay flat, so I made a partial gasket from a matchbook cover and filled the gap. It all went back together quickly. Just have tools ready beforehand. Ten minute job, unless you have to make a new gasket or part of one. Thanks, guys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Durham, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost build up in ice maker
Watch online video on how to change icemaker flap! Video was great exactly how to do it, with a link to order the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Mooresville, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Dispenser Door Seal not sealing, frost in freezer
Googled how to replace the door seal, ordered parts and replaced the door seal flapper. The video on partselect was not correct for this GE model. However a simple diagran showed you simply remove the control panel directly (pops off) to provide access to the panel. Remove the 4 screws holding the panel, replace the door seal, and reassemble.
Was this instruction helpful to you?
Thank you for voting!