GSG22KEPCFBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kenneth from Milford, CT
- Parts Used:
- WR23X21444
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer Light switch broke
Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from SILVER SPRING, MD
- Parts Used:
- WR60X24484, WR60X10209, WR02X10520
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Noise coming from rear of fridge
Remove rear plate. Remove fan bracket. Replace fan gaskets, blade and motor. Replace bracket. Replace rear plate. Very simple. Fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Javier from Woodstock, GA
- Parts Used:
- WR17X11170, WR49X10233
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Unit was not dispensing water nor ice.
Removed the plastic frame by pushing to the inside (all 4 sides), removed touch pad by sliding it to my right and disconnected the wires. Removed the four screws that hold the dispensing unit and replaced broken parts. Please note that I also replaced the funnel. Total cost of repair for DIY $30.00, savings by avoiding repair man, priceless.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John H. from Claremont, NC
- Parts Used:
- WR17X23191
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
apiece of the ice bucket broke off and would not hole ice
Removed the ice bucket and put the new ice bucket in placed
.
work like a top.
.
work like a top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from SPRING HILL, FL
- Parts Used:
- WR17X11505
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice Would Not Come Out
Removed tray, threw out ice , removed 3 screws used 2 screw drivers to seperate part & re installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from FRANKLIN SQ, NY
- Parts Used:
- WR23X37285
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
light not working
I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachel from LUDOWICI, GA
- Parts Used:
- WR50X10068, WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Would not defrost
Replaced defrost thermostat along with temp sensor watched the video on this page simple fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from NEW YORK, NY
- Parts Used:
- WR02X10520
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Noisy refrigerator
I visually inspected the compressor and narrowed down the source of the noise to the freezer area. Then I removed the doors and the screws securing the divider panel. Next I removed the bottom panel of the freezer, the styrofoam insullation panel and the evaporator motor. The motor is mounted between two grommets. I replaced the grommet facing the fan blades. The aluminum reflector below the styrofoam insulation panel had also come loose. I reattached it and reassembled the refrigerator in reverse order. The noise is gone!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Graysville, TN
- Parts Used:
- WR17X23191
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rotating "auger" in ice bucket bent/jammed.
Took out the old, put in the new. Problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randolph from Lynchburg, VA
- Parts Used:
- WR60X10074
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Refrigerator was noisy when running. The noise increased with time and got so loud it hurt your ears with a high pitch sound.
Empy all the food from the freezer and remove the ice container and the lower ice maker section with a 1/4 inch nut driver, unplug the unit and set aside. Remove all shelving and set aside. Remove light cover and unscrew the bulb and remove. Remove cover/with light fixture by removing the necessary screws with the nut driver. The cover has the fan assembly attached; unplug and remove fan assembly, remove the thermistor from coil attached with a clip. Reassemble in the reverse procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Blountville, TN
- Parts Used:
- WR29X43990
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice Maker Auger replacement: part # PS1018130
I agree with the other posts that suggested taking a picture of the blades and spacers before taking the auger out, makes it so much easier to put it back together in the same way. The only difficult part was holding the two tabs apart while removing the unit, you need a second person to help with this. I used two small screw-drivers to gently pry the clear plastic box away from the white plastic holder, while my helper pulled the holder loose. Keep in mind that the plastic nut that holds the auger in place is a left hand thread. Went back together very easy and it's working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Naz from Rocklin, CA
- Parts Used:
- WR02X11330, WR17X10745
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Plastic water line leaking
Removed the bottom front cover, under the two doors, unclipped the water line to have better access, removed old Union connector, cut about a 1/4' off each side of the line, pushed both sides of line in Union Connector, checked for leaks, all done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from loxahatchee, FL
- Parts Used:
- WR32X10834, WR32X10835
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
pans were missing
just put them in the proper shelves
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stan from eureka, MO
- Parts Used:
- WR29X43990
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
plastic auger blade broke off
removed 4 screws in order to view and remove auger. removed metal and set washer on back of auger. This step not difficult. This will release auger from plastic ice resovoir. Again, not difficult. Remove plastic nut after removing auger. This procedure will release crushed ice blades and 5 plastic washers, 3 flat and 2 raised. You have got to remember order of blades and washer. Again draw diagram take pictures. Very, very important. Put back as taken apart. Good Luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregh from Wittmann, AZ
- Parts Used:
- WR17X11497, WR01X10315
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The Auger had broken blades and cover broken
To take the ice dispenser apart is not difficult. A ring removal tool would have helped to remove the auger. The Auger nut was difficult to remove and I used a visegrip to pull it off. Once the retaining ring was removed the repair was easy.
Never did it before but figured it out.
Never did it before but figured it out.
Was this instruction helpful to you?
Thank you for voting!