TFZ22PRBEBB General Electric Refrigerator - Instructions

Easy repair. No need to remove the door. Simply prop up the door with blocks or books - remove hinge and riser assembly - replace with new parts. Total repair time about 15 minutes. Tools needed only an open end wrench.

ordered drawer face - perfect part- snapped right in. done. order came within 10 days.
will order again if needed.

Concerned about removing and attaching front panel to broken drawer. Rep. said wasn't sure but most just snapped together. Rep. was correct. No tools required.

Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.

Followed the video on the computer. Was fixed in no time. Works great.

There are Great videos on YouTube!!! Turned off power,Removed trim ring, Pushed a philips head screwdriver in one of the holes underneath the electrical panel with the selector push buttons. This releases the electrical panel. There are Three wire sets with plugs. I removed the plugs and took the electrical panel out. Removed four Phillips head screws and pulled out the big paddle switch. This then exposes the flapper. Replaced flapper with new one and reassembled everything. When I had everything apart, I cleaned with window cleaner. It was pretty moldy from the water leaking. Turned power back on and tested everything to make sure I didn't mess anything up. Works great

First I pulled the door up to the top hinge and propped it up with phone books. Secondly I used a nutdriver with an 8mm attachment and removed the bottom hinge. Thirdly, I removed one screw from the bottom of the door with a socket and 8mm attachment and removed the broken cam riser. Being careful as to take note of how the cam was positioned. I then attached the new cam riser to the bottom of the door, attached the bottom hinge to the refrigerator, making sure the pieces (cam riser and plastic on bottom hinge) matched up and after everything was tight, removed the phone books. Remember to first remove the vent on the bottom of the refrigerator and it is much easier to maneuver the door if you empty the contents on the inside. Very easy, I am not very mechanically inclined and this is the first job that I finished in the amount of time as stated. Also, do not chance just the riser as both pieces will be worn. Hinge assembly comes with all you will need.

Really simple, I used a can of soup and a small piece of wood set under the door, and tapped it tight with the hammer to hold it in place while I removed the hinge. Two bolts at the bottom and two under the door itself. Installed the new hinge set, bolted tight and removed the shim.
The whole thing took less than 5 minutes

I just followed the instructions on the video and it was exactly as they said......no surprises.

Remove front cover did not remove wires remove ice and water unit took off flapper put new one on 5 minutes back together

Unplugged the refrigerator then used the cordless drill to remove the 6 screws on the access panel on the back of the fridge to be able to get to the fan. Was able to pull the fan off by hand and push the new fan on by hand. Plugged the refrigerator by in and watched the fan run for a few minutes then replaced the access panel. Really quick and easy repair.

the previous left behind a side by side, everything worked however the auger in the ice bucket was a little rusty. I wish that I could say it was all me but the truth of the matter was the videos on file.

They were nicely done and easy to follow as I took the unit apart and replaced the auger in about 30 minutes. Thanks for all your help in part look up.

Part attaches to metal plate near crushing fingers which attaches to ice holding bin. Remove about 6 screws total on each side of plate. You must disassemble the auger & other parts so you can reassemble it in the proper order. Not many parts but i always take pics to cut down on time. New part is at the other end of the auger and acts as the holde of the auger shaft. Picture a crankshaft with a bearing on each end so the auger rotates between new part and the other end of auger shaft. That's it.

It seems my refrigerator was old enough [1987] that the spacing on the holes for the bracket were different than the part that is currently sold. The holes on the new bracket were 30 mm apart on center, but on the old bracket they were 20 mm apart on center.

Clamped the old and new brackets together in a vise to use the old bracket for spacing and drilled a new hole through the 4mm of steel.

After which it was a snap installing the new hinge assembly.

Replaced flapper. Followed the video. The lamp caused the removable plastic bracket (which supports the control panel and the ice chute) to fuse with the plastic frame in the door. Eventually broke the fused plastic, removed the bracket, and filed the rough broken plastic before reassembly.