MSX25DRZBWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JACOB from COLLEGEVILLE, PA
- Parts Used:
- WR62X23154
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Only crushed ice. No cubed.
Found a step by step video on YouTube made replacement very easy. Cubed ice is back. Time for a cocktail to celebrate!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from HOSCHTON, GA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Frost collected in the ice dispenser shute clogging it
Replace the flapper and this solved it. The video provided was excellent and allowed me to do this repair myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from MADISON, WI
- Parts Used:
- WR30X256
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken plastic on ice hopper that helped stabilize the auger
Emptied hopper
Removed screws to remove auger from existing
This was so easy I impressed my wife
Removed screws to remove auger from existing
This was so easy I impressed my wife
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jabe from Little Torch Key, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
In-Door Dispenser Didn't Work And Leaked Water
1. Use skewer to press plastic tabs under control panel, 2. Remove control panel and unplug solenoid, 3. Unscrew dispenser assembly and solenoid screws, 4. Press in tabs on lamp and remove assembly - unplug, 5. Replace lamp assembly, 6. Replace solenoid assembly and fasten screws, 7. Replace flapper. 8. Replace other parts in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberto from Wildomar, CA
- Parts Used:
- WR17X2062
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
rusty plate in the ice dispenser.
removed the dispenser and disasembled it repaced plate and reasembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from North Topsail Beach, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice dispenser chute icing up
Replaced dispenser flapper
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Chester, SC
- Parts Used:
- WR17X3089
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
I had a soleniod and the crank assembly to got bad.
First, I had to remove the face plate where the ice and water was dispensed remove 4 screws holding the electrical circuits, disconnect circuits ,remove 2 screws holding soleniod and one screw holdin crank assembly. repace parts and screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from THE VILLAGES, FL
- Parts Used:
- WR62X23154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker only dispensed crushed ice.
Determined that the little door that opens to allow full size cubes to fall was not opening. If you open freezer door, hold door switch in, select cubes and push in the lever that the glass pushes in you should hear the solenoid lift open which opens the little door. Mine was doing nothing. Removed ice bin and then removed icemaker motor/solenoid section from back of freezer by disconnecting two wire harnesses and one screw. Found that solenoid smelled burnt and could see that inside of the solenoid was swollen out of round and burnt. Simple to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Naples, FL
- Parts Used:
- WR17X4312
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Bucket got a hole in it and Auger would not work
Removed the 4 screws off the old bucket cover and place the cover on new bucket. Just that simply. Can't beat the price!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Arlington Heights, IL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost on the bottom of the ice bin frome warped rubber flapper
Pulled the outter cover off, removed the electronic board, replaced the flapper and put it back together again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chad from Wichita, KS
- Parts Used:
- WR17X4312
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Ice bin rusty and replaced thermostat and defrost timer
the ice bin was a cinch with the complete part ordered from Partselect.com. Just had to replace the old faceplate onto the new part put the ice bin back in the freezer and voila. Didn't really need to replace the thermostat but did anyway with the defrost timer and then the thing started keeping temperature again. Thanks a bunch! I just hope the refrig will hold up a few years longer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manuel from Winnetka, CA
- Parts Used:
- WR17X4312
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I do not have an Ice Bucket.
I neeeded an ice bucket for a refrigerator that was given to me. I wish if I could have oder the whole part as a whole.So, this is what I did. I order the Auger and Ice Bucket Assembly.Later, I realize when I received the part that I also needed the Cover bucket assembly and the Ice storage door.Now I do not know if when I get the rest of the parts if it also comes with the screws that hold the cover bucket on or if I have to order the screws separate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- VINCENT from SPOTSYLVANIA, VA
- Parts Used:
- WR17X3489
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Tab that holds light shield was broken off.
Removed ice tray and set on kitchen counter .One small phillips scredriver to remove broken tab.
Attached replacement shield with screw, replaced ice tray. Probaly total of 5 to 10 minutes to find scredriver, do the repair & replace screwdriver where it belonged. Took more time to place order then do repair. Add a couple of minutes to unpack.and some more time to drop off cardboard box at recycle center.
Attached replacement shield with screw, replaced ice tray. Probaly total of 5 to 10 minutes to find scredriver, do the repair & replace screwdriver where it belonged. Took more time to place order then do repair. Add a couple of minutes to unpack.and some more time to drop off cardboard box at recycle center.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from University Place, WA
- Parts Used:
- WR17X3489
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken part due to age
Super fast replacement, and the part was sent to us FAST and WELL-PACKAGED and REASONABLY PRICED! Thankyouverymuch!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Atlanta, GA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost was building up inside the freezer just above the ice dispenser shute.
Followed the instructions and replaced the door recess.
Was this instruction helpful to you?
Thank you for voting!