TNX22BRCBRBB General Electric Refrigerator - Instructions

I ordered the replacement from you guys, got the new ice maker and the plug had an adapter, but it wouldnt fit in with everything. So I cut the plug off my old ice maker and put it on the new one and it works just fine.
thanks for everthing P.S. i got the ice maker from you for 109.00 and sears wanted 130.00 for it
good stuff good deal.

i did every thing according to instructionwhich was simple but it did not cover how to use the extension electrical plug-in and where to put the extra cord so the tray would go back in

A friend had no problem getting the new ice maker in. But then the problems started. The ice maker works great. But when the water fills the ice maker it squirts water onto the side of the freezer and ice sickles form. So we watched and decided the hole was too large so used a piece of plastic. That helped to cover the hole. But some water is still entering the freezer and not all going to the ice maker. The only other thing we can think to try is to use epoxy to try to close that place. A simple job has turned into a big headache. I wish they made the ice maker like the original one.

Removed ice dispenser trim from bottom-up and then removed control panel by gently pulling up from the bottom. Removed four screws holding dispenser chute and then two screws holing flapper assembly. Replaced gnarly old flapper with a new one and put all removed pieces back together.

Watched video on website then removed old ice maker. New one went in without any problems. Working great. I am a 60 year old woman and had never done anything like this but so easy. Husband scared now, doesn't know what project I will take on next.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

The instruction video was great, mine was easy than even the video showed it to be. I changed it out in less than 15 minutes and it works great. The niocve things I didn't have to wait for a repairman or my husband to fix the problem.

REplaced old icemaker with a new one. Install simple, However that was not the problem. I then replaced the water valve. Still no ice. I check the electric connection was OK. THe problem was the elbow fitting on the top back of the refrigerater leading to the icemaker was blocked with ice.Cleared it and turned water faucet up all the way. Ice maker worked.

The video on the site was very helpful. The repair was really easy. It was exactly the way the video showed how to do it. I would definitely use this site again to find parts, figure out the "how-to", and use for skematics of appliances. Thanks.

turn off water. turn off electricity. empty freezer section of frozen food. remove ice bucket. loosen two screws holding IM to wall of refrigerator. lift off icemaker, and then unplug it as you remove it. INSTALL new IM by: putting new water funnel onto new IM. attaching adapter cord to IM. plug in IM electrical cord to refrigerator and then hang the new IM onto the two loosened screws on the refrig wall. Now tighten the two screws. the extra adapter electrical cord hangs below the new IM, but does not get in the way when you reinstall old ice bucket. reload food, turn on elec and water. PS. i had a crack in the casing of the new IM, so i got a new one, but that one was cracked too. so i just installed the second cracked one. hope it is not a problem.

remove the 'pop-out " frame around the door recess, you pry the flexable seal from around the ice despenser, have someone hold the unit with the wiring, remove the one screw that holds the door recess, and replace the new one. reverse the procedure. remember to unplug thr frig. first

install icemaker water was allways delivered to previous unit water is not being delivered to icemaker still having difficulty

Part 2 (screws): I let the refrigerator warm to room temp overnight. I took off the freezer shelf brackets and light, and then the bottom of the freezer compartment using a dime to pry it up (tricky). I poured water into the drain under the coil and it drained very slowly. OK, the drain line's plugged somewhere and it's not ice. I took off the back cardboard compressor cover, unbolted and pulled out the fan, and saw the drain tube in the drain pan. There's a little hole cut in the side of the tube. I took a 6 ft length of plastic trimmer line from a lawn edger/trimmer and ran it through the hole and all the way up the drain line. Water started draining out! I jiggled the line around some to make sure it was clear, then I replaced everything the way it came apart. The white painted freezer screws had lost their paint since this was the third time in 4 years the freezer had been dismantled before diagnosing the plugged drain line. The first time this happened, (at age 10 years (not me-the refrigerator)) I called a repairman who said I should just replace the refrigerator since this brand was no good. He was wrong - he just didn't know how to fix it and now it's working fine (plus he lost one of the screws). I really like my now 14 year-old GE Profile refrigerator and I'd buy another (plus it was made in the USA!!) Second time, I took it apart myself and failed to notice the drain was partially plugged with something (I assumed it was frozen). Part 1 (slide cover): The other repair was the right bottom shelf bracket got broken somehow. The replacement bracket from PartSelect was identical to the original and the repair was easy, except it took me a while to remember how it went together. Thanks and I hope you like my trimmer line ldea. Support our economy - buy American!! Thanks PartSelect. Signed GR in Corpus Christi, TX.

Had to take front panel off dispenser area. Then remove components and install new part. That was easy part. Problem was getting components back into front of freezer. Seemed like something was blocking it from going all the way in. Had to remove small amount of insulation and "jiggle" components and eventually fell into place.

Installing the actual ice maker was quite easy. What takes most of the time is preparing the freezer for the install. Need to remove all shelving, (and the door) to gain access to the unit. The ice maker is simple to install once access is achieved. Putting everything back together takes some time.