TFG24PRSMAA General Electric Refrigerator - Instructions

Removed screws holding top door hinge. Lifted the door off bottom hinge. Unscrewed cam from bottom of door. Drilled out rivet holding the second cam in the bottom hinge. Replaced both cams using a flat headed bolt to hold the bottom cam. Dropped door into bottom hinge and replaced top hinge screws. Job done.

Make sure you buy two cams and have a bolt to replace the bottom rivet.

Not a difficult job as long as you have a drill !!!

Replaced the old cams with new ones, door works perfect now.

Thought I would only need one when I looked at the picture of the parts. Decided to order two just in case and after taking it apart both were broken. Needed two.
Took the top door bracket off and lifted the door off of the bottom bracket. Re-assembled cams, put a little white grease on all moving parts, placed the door into bottom bracket and installed top bracket. Adjusted top bracket to make door line up with edge of refrigerator and all is well.

The bottom of the door was 5 " off the floor. A 2x4 block and a 4x4 block were pushed under the door and supported it while the water line was disconnected the hinge removed and the cam replaced. It was a simple fix and reading other people's experience made the repair so much easier.

Transferred ice supply to another freezer. Removed ice maker unit from freezer and studied assembly. Removed the 5 screws holding the bucket in place while keeping track of which screw went where. The only positional component to remember was the motor control pivot retainer. Wiggled and fiddled to remove the old bucket. Wiggled and fiddled to put the new bucket in place. Replaced the 5 screws, dumped the reserved ice back into the bucket, and returned the ice maker unit to the freezer.

First of all, It was Christmas and no extra money to pay a repairman.
i got on the computer and started looking for a parts breakdown for an older GE side by side.
I finally found it and located the part I thought we needed.
I looked at several parts dealers and yours had the best price.
anyway it arrived in just 2 days. My son helped me remove the door and we put the new part on and I just saved the cost of a service call.

Thank You

Door needed to be supported before hinge assembly was removed. After replacing broken cam doors aligned and doors closing properly.

1. Unplug the fridge
2. Removed the outer facing of the dispenser outside the freezer door. This is fairly easy, better with a tool (plastic scraper) that won't mar the finish.
3. Removed the plastic plate with labels -- water, ice, etc. This is done by sliding a small jewelers screwdriver into the slots on the left, middle and right in back of the plate. These are difficult to see without a flashlight.
4. Removed the four screws in the panel behind this plate.
5. Unpluged the large cable on the left side after the panel is freed.
5. Removed the rubber "dispenser" button. this just pulls off.
6. Remove the panel
7. Lift flapper up and remove. Clips hold this in.
8. Put new flapper in place.
9. Use reverse order to put back together.
Piece of cake. Ice maker no longer frosts up.!!!!

Before disassembling the parts need to replace, I use my digital camera to get all the different angle of the item so I have the full reference to asswmble the new one

i'm glad I read this forum before ordering the part because you need two of the door cams. They're sandwiched together on the lower hinge.

I removed the top door hinge, lifted the door off from the lower hinge and layed it on the counter.

I then removed the lower hinge using a nut driver.
I had to grind the rivot head off that holds the door cam onto the hinge and use a nut & bolt to replace
the rivot.

I took the top over off the pivet bracket and used a nut driver to remove the screws on the pivet. Lifted the door off and put on some saw horsess. I revoved the pieces of the old cam on the door by taking out the screw and put the new cam back.
I then drilled out the rivet on the bracket on the door and removed the broken cam. replaced it with the new one and used a screw and nut to replace the rivet. Put the door back and works great now.

completely removed door, then replaced worn-out cam on bottom of door-simple enough; then removed hinge from bottom of refrigerator; removing old cam required drilling out the rivet that fastened cam to hinge; secured new cam to hinge with small machine screw and nut. This procedure is relatively easy but does require minor mechanical ability and having a small drill and bit set. However, replacing the two cams totally fixed the problem.

I did not realize I needed 2 cams to complete repair. Door cam was riveted in. I had to drill out rivet and replace with nut and bolt. Otherwise it went quite sommothly. At first I just replaced the cam on bottom of refridgerator but door was not quite right when closing. Further inspection showed the door had the other half of cam that also needed replacement. Needed 2 orders. Paid for 2 shippings.

Firts I removed the food from the freezer. Then I used the cordless drill/screw driver to loosen the broken piece of plastic. I inserted the plastic shield and screwed the shield in place. The majority of time was spent removing and replacing the food from the shelf.

Finding the part was made so easy by this website. I wish I had done it years ago but because I am not handy, I didn't think I could do it. Reading how easily others did it convinced me to try.

removed top plate and raised the door off. I removed the L bracket from the fridge then noticed the part was rivited onto the L bracket. I cut the rivit and replaced the cam and used a small bolt and nut to sdecure it. Replaced the L bracket, the door, and the upper support. Only problem was the surprise rivit