TFX24FLJ General Electric Refrigerator - Instructions

Disassembled ice-maker, noting what screws went where, what direction ice release control arm pointed, and noting how the control arm spring was mounted. The door assembly comes off first followed by the circular assembly that houses the ice door and last grinding arms. It is quite easy see how it comes apart as you look at the screws. Remove the screw holding the back end of the control arm and note the spring position. The control arm needs to be turned to line up notches to pull it thru a faceplate hole while rotating the arm about the "U" that is on the outside of the faceplate in the door housing. There is a retaining clip holding the rotating impeller to remove to complete the dis-assembly. Use vinegar to clean rust out of bin and other parts around the faceplate. Assemble the unit in the reverse order to complete the job.

First we removed the door. Then we had to hammer the old part off including the old rivot. We fould a screw that fit and put this piece on. We held the door in place and screwed the hinge on the main unit.

First I took everything out of the fresh food door, then I removed the top hinge cover using a philips head screwdriver, and a nutdriver for the two screws holding the upper hinge. Lifted the door off the bottom pin, and placed it on the floor. Then took off the bottom hinge and used the Dremel tool to grind off the rivet holding the broken door cam on the bottom hinge. Used a nut and bolt to hold the new cam in place, and put the lower hinge back on. Then replaced the other cam on the bottom of the door itself, using the nutdriver. (Be sure to buy two cams, and have the bolt and nut to replace the rivet). Reinstalled the bottom hinge, put the door on, replaced the top hinge, and presto! Works great! Thanks to the others on this site for their stories - really helped make it an easy and quick repair!

First I removed the top hinge of the refrigerator door and then lifted it off the bottom assembly. I had to turn the door on its side to work on the bottom where the broken part was located. I unscrewed the bottom assembly and replaced the broken part with the new door cam. Put it all back together and now the door closes but must be manually pushed to close. When the door was working properly it would shut automatically when released from any position. I think I need to install an additional part - maybe a shim? to make it close automatically. That will be another story.
This was a fairly simple jog to do but since I did not have the proper tools it did take me longer than usual to remove the bolts. I'm happy I did it myself and saved a big repair bill! Thanks to the people at PartSelect.com.

Ordered at PartSelect and received the auger and blade within days. Printed the parts diagram and proceeded to take the auger apart the time it took would have been much less but I seized the opportunity to do a deep cleaning of the old parts before replacing them....The part diagram was the key to simplicity and the fast shipping was awesome. Thanks I'll be back....

Removed the top hinge cover held by one screw. Removed the top hinge held by two screws and them lifted the door up and off the bottom hinge. Laid the door on the floor and replaced the cam piece from the kit on the bottome of the door. That required removing one screw and losening another. Removed the lower hinge (two screws) and replaced it with the new one in the kit. The lower hinge includes the other cam piece. Lifted the door onto the lower hinge and then replaced the top hinge and cover.

Part attaches to metal plate near crushing fingers which attaches to ice holding bin. Remove about 6 screws total on each side of plate. You must disassemble the auger & other parts so you can reassemble it in the proper order. Not many parts but i always take pics to cut down on time. New part is at the other end of the auger and acts as the holde of the auger shaft. Picture a crankshaft with a bearing on each end so the auger rotates between new part and the other end of auger shaft. That's it.

The old cam had broken and was on the floor. I ordered one new cam. I should have been told to order at least two, I did not know they worked in pairs. So I had to re-order, I ordersed four, I was able to see that the other (freezer door has cracked cams) door will soon need replacement of the cams. I had trouble installing the new part because the rivit also needed to ba replaced. I did a "Rube Goldgerg" to get the new part to sit properly. I drilled the hole open a little and forced the part into place. All is well. Thank you very much!

I simply removed 6 screws that held bucket to face and pit on new bucket and put it back in freezer works great

We only needed the rear plastic cylindrical helix. After installing it, there was a squeal of metal on metal due to insufficient clearance between the rear moving blade and the Ice dispenser plate.

Refrigerator Ice Maker 7/16” (or ½” hole, stainless steel) washer just behind #334 Rear Moving dispenser Blade PS292310 to give clearance so it doesn’t hit #345 / PS292441 Ice Dispenser Plate.

This was my first time at doing this so it took longer than someone experienced. But, it worked!

This was a 15 year old great working GE regrigerator. Refrigerator was not cooling properly, though the freezer worked great. Using flashlight, examined cam riser which was clearly broken. YOU MUST ORDER TWO GASKETS AS BOTH WILL BE WORN. After removing all food from the door, taped plastic sheet over the open space to keep food somewhat cool Removed top hinge cover and screws on top of door and lifted door out of bottom bracket placing it flat on kitchen island. Unscrewed hinge elements including old broken cam and shims form the bottom of the door and fit in the new cam. Unfortunately one of the shims was broken, so I used a thin plastic black washer from the hardware store which was big enough to fit over the pin on the bottom of the refrigerator itself. Screwed all the parts back together. Be VERY careful to note how you removed them in the first place...mabe take a digital foto or two. This was kind of tricky to remember. Then used a hammer and chisel to break off the rivit holding the bottom hinge elements on the refrigerator. Sawing with jigsaw didn't work that well. The rivit came right off. Then used a flat head screw, lock washer and nut instead of a reivit and attached the new second cam riser. You are now done with the new parts. Simply reattached the door and it closed like new. Had a simultaneoius problem with a faulty defrost heater in the freezer which also had to be replaced and which was really easy to do. About an hour max. This was the real cause of the refrigerator not cooling properly. But that's another story.

Same problems as already described .... door would not close, plastic bits on floor, angry, ready to throw-out 15 year old “dog” and blow at least $1,000 on a new appliance!

This repair is dead easy. Remove the two bolts holding the top hinge and lift off the entire door. Don’t be surprised if the original Riser Cam has virtually disintegrated, mine was a wreck. Remove two bolts that retain the old flat metal “shim” and fiber “gasket”.

Fit new Riser Cam and re-use old shim and gasket. Replace door on dome-shape bottom hinge mount and then re-fit top hinge.

If in any doubt order new shim and gasket along with the new cam riser. Or, do as I did, and “manufacture” either of these parts from scrap material found in the workshop ....

1. Put all perishable food into ice chest. Empty door shelves.
2. Remove top hinge cover with Philips screwdriver.
3. Supporting door, remove top hinge attached by two hex screws.
4. Lift door off bottom hinge.
5. On bottom of door, unscrew the hex screw holding the broken plastic cam.
6. Loosen the second hex screw enough to free the broken cam.
7. Replace the cam and tighten the hex screws making sure the opening of the cam lines up with the hole under the door.
8. Snap off plastic grill at the bottom of the refrigerator.
9. Remove bottom of the two hex screws holding the bottom hinge tot eh refrigerator body.
10. Loosen the second screw enought to rotate the hinge upsidedown. Tighten the screw again.
11. Now the rivet bottom is exposed so as to facilitate drilling it out to remove the broken cam.
12. Loosen the hex screw again and turn it back rightside up. Reinstall the bottom screw and tighten both of them.
13. Using an appropriate size bolt, lockwasher and nut, install other new cam.
14. Reinstall door reversing steps 1 to 4.
15. Don't forget to return the food to the 'fridge, by the way!

took top bracket off--then removed door--took
bottom bracket off bottom of door and replaced
door closing cam and reasembled---a piece of
cake

The plastic door closing cams had broken after 17 years of use. It was tricky figuring out how the new cams fit as the old ones had disintegrated. Also you need 2 cams - not one. I first ordered only one. A detailed parts diagram would have helped. First unscrew the top door mount cover and then the top door mount. The fridge door then lifts up and off the lower door mount. Next is the hardest part - drilling off the old pop rivet which held the lower cam. The lower door mount had to be removed to get at the underneath of the pop rivet, and a bench vise was handy to hold it as I drilled off the old rivet. Then you need small stainless steel nut and bolt and split washer or lock nut to replace the rivet. Next unscrew the old upper cam from the underneath of the fridge door and replace. The large hole in the cam goes through the door hinge pins. The two plastic cams should interlock in a way that makes the door swing close. Anyway, now the door works fine.