GBS22HBRABB General Electric Refrigerator - Instructions

I easily removed the screws and then removed the board and took a picture so I would remember how to re-connect it. It was really easy and now my refrigerator is working great. If I can do it anyone can do it. My husband was amazed that I did it all by myself.

was not home when part came so my wife installed it enough said

Moved fridge out from wall. Unplugged. Removed circuitboard cover 6 screws?). Replaced circuit board (showed burn spots on back side). Replaced cover and plugged back in.

I pulled the fridge out away from the wall, unplugged fridge, and found the panel that the main control board was behind. after comparing old board with the new i unpluged all of the connections unscrewed four screws and installed new board in reverse order. very simple..

replaced the temperature sensor and the defrost thermostat a couple of weeks ago, but did not solve the problem. went ahead and replaced the main control board, and i'm back in business. thanks to the how-to video's at this web sight, the job was easy.

Unplugged side by side took about 4-5 screws out removed plate from back, unplugged the wires removed old board and plugged wires in new board, note: new board a little different than original. Screwed plate back in. So far so good. I do not think I will buy any more ge appliances, this one was very expensive but out of warranty now my ge dishwasher is making noise all purchased at same time.

I checked the problems others were having to see if they had simular ones. They were having the same clicking noise I was having. My refrigerator would not turn on. Clicking noise but would not start. They replaced the motherboard. I searched the internet for prices. Part select was about $30.00 cheaper that the other stores. I ordered from part select. Nice helpful people to deal with. I installed the part in about 5 minutes, very easy repair. They sent me an updated part. Thanks everybody and Part Select for your help.

very easy repair, simple exchange

disconnected wire harnesses, popped out old board, popped in new board....5 minutes

I read other reviews then decided it was my main control board.Watched the video for install. It was easy to change out.Everything is working great again.

read on line that fan control in main board can cause erratic running of the fan causing "whooing" and ghostly sounds. New board installed and now I have the quietest fridge in the neighborhood. Here's the unbelieveable part. Ordered the part online from parts select on good friday morning. Fed ex delivered it just after lunch the next day (saturday). Now that's the best service I've ever received!!

I unplugged the unit, replaced the main board, repowered and observe for a few minutes. my fridge is okay again.

Ice & Water dispenser did not dispense. When pushing on the dispenser lever, the entire unit briefly lost power and reset as though the appliance was unplugged. I heard a click from the back of the unit where the main board was located.
Fridge made ice but didn't operate. I determined the micro-switch and solenoid were working properly. So the only thing that could be wrong was the board.
Removed main board panel with screw/nut driver. Unplugged board connections. Un-snapped main board from housing assembly. Installation is the reverse.
Very easy. Only needed was a screw/nut driver. Electrical connections are easy since the harnesses can only fit to their own connection. No way to make a mistake.
Took no more than 10 minutes.

Problem solved!

Partselect.com has a great video on how to replace the main control board. Very easy to do this repair.

It took me less that 5 minutes to complete.

Once the part was replaced, my defroster in the freezer is working perfect. The ice and water dispenser is working, too.

I saved myself $$$ going through Partselect.com rather than calling a repairman or replacing the fridge.

I unplugged the refrigerator. I removed cover plate with nut driver. I removed all wire harness plugs from old board and removed old board using needle nose pliers to squeeze existing holding clips. Old board came right out. I then snapped new board into place and replaced all the plugs. I replaced cover with nut driver and plugged in the refrigerator. Its been two weeks and all seems to be working fine.