MSK25GRBGAA General Electric Refrigerator - Instructions

Under the control panel there are three small holes. Insert ballpen or small flat screw driver on both outer holes to push a tab lock that holds the control panel in place. Then pull out control panel and three set of wires will be exposed and disconnect wire connectors (connectors have different sizes so you wont get confused in reconnecting). Unscrew four screws on each corner that holds the ice dispenser assembly (a part where you push your glass against to dispense ice or water. The flapper is exposed and easy to replace.

Excellent video was available on the Parts Select website. It was simple. The selector panel pulled out by hand from the bottom. The subpanel was removed with the four screws. The flapper snapped out of the holder with two clips. The new one was inserted in reverse order.

Video is a great but still need to read the instuctions because there are parts you may need on the old ice maker. Saved myself a bit of money by not having to call a repairman. The process was very simple. I am glad I did it myself. Thank you Parts Select!

Replace the flapper and this solved it. The video provided was excellent and allowed me to do this repair myself.

Part was easy to find on website. Part was delivered quickly. Reapir was easy, just replaced old hinge with new hinge.

Not really sure of the age of this fridge, as we bought the house 2.5 yrs ago.

I'm one who if it can go wrong, it will, so not realizing how stable the door was from just having the top hinge and the magentic gasket, I declined to prop the door up on blocks the way some guys say the did, and instead removed the top hinge and lifted the whole door off the bottom hinge. I traced the outline of all parts with a felt pen before removing them, figuring I'd need witness marks to help with realignment after the install.
Nut driver might've been an easier choice than the socket set, but the only ones I have a brittle and I've broken the 5/16"...
All parts came out/off easily. The new bottom hinge and the old top hinge (both on the fridge side) practically aligned itself right on my marks, and the new cam (door side) just needed to be held while the screws were tightened. I used the extensioni rod off the ratchet to drive the screws most of the way (making a nutdriver out of it).
Parts were exactly as advertised, although there was a note in the package that stressed the need to replace both parts at the same time due to material differences in the original and replacement parts. Since the cam is sold separately without the hinge, it would be good for the website to reflect that before the purchase is made. Also, even though it was only the cam on the hinge and not the whole hinge that needed to be replaced, I could've bought hte two cams separately and drilled out the rivet as another person had done, but for the $5 difference in cost, why bother?
Door now closes itself as designed, albeit slower than the freezer side, but the Wife says it always did that.
Also interesting that when first assembled, the door DIDN'T close itself at first... not sure it it needed to wear a litle, or if it just needed the added weight of having items back in the door shelves.
Love the great website... just typed in the model number and the parts I needed, complete with drawings to make sure, were right there. Great UI.

removed the door hinge assembly & replaced it with the new assembly.

Remove the hinge cap on top, the loosen the bolts, remove the hinge. Pick up the door from the lower hinge, lay it down and place the cam riser on the lower hinge. Replace the door, install the top hinge and check the alignment and you are done.

Supported the door on the bottom them removed the 3 screws holding hinge to door. Installed new hinge assembly. Had a litle trouble installng screw in bottom of door due to alignment issues with cam & metal piece. It finally went in when I loosened 2nd screw in bottom of door.

Emptied hopper
Removed screws to remove auger from existing
This was so easy I impressed my wife

unplug refrigerator. Remove Ice bin then remove the cover off the ice maker,(slides off from bottom then lift off top) no reason to remove ice maker completely. Remove center gear screw and remove main gear from Ejector blade. remove (3) screws holding the front plate. The motor and switches are attached to this plate from behind, do not remove the nut from the from the stud that adjusts the travel for the motor. The Motor and switches will come upt with the plate and the shut off arm will come out of a hole in the top right. Its ok just be careful when you put it back to get it in the hole. remove the old cam and replace it wint the new one and reassemble. Its a bit tricky to get all of the microswitches over the new cam just carefully wiggle the plate and cam and don't push too hard. once everything is lined up it should go back together and you can replace the screws and main gear :)

First, I had to remove the face plate where the ice and water was dispensed remove 4 screws holding the electrical circuits, disconnect circuits ,remove 2 screws holding soleniod and one screw holdin crank assembly. repace parts and screws.

If a 74 year old guy can install an ice-maker in a 20 + year old fridge in 20, or so, minutes it must have had good pictures and BIG PRINT. Working quite well at this time!

Ice hopper had no ice in it. But water in door worked and if I added ice to hopper, it would dispense in door. I added water to ice maker but no ice was made. Replaced ice maker and all it required was to unplug harness and remove two screws with nut driver. Easy!

Replaced dispenser flapper