Models > TFX30PRYEAA > Instructions

TFX30PRYEAA General Electric Refrigerator - Instructions

Jump to:

All Instructions for the TFX30PRYEAA

Customer:: jon from social circle, GA
Parts Used:: WR17X11653
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

frost formed because the ice damper let warm air into the freezer

Removed frame, unscrewed the electrical panel, and popped the flapper off. Installed new flapper. Replaced the electrical panel and re-installed the frame.

Was this instruction helpful to you?

Customer:: Charles from Spring, TX
Parts Used:: WR62X23154
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

Refrigerator was only dispensing crush ice and not cubes

Solenoid pushing the crushed ice flapper was burned out. Solenoid was easy to find unplug and replace. I used the old piston which simplified things. Now works great

Was this instruction helpful to you?

Customer:: James from Marietta, GA
Parts Used:: WR17X11653
Difficulty Level:: A Bit Difficult
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Frost inside freezer door and water dispenser line freezing

I followed the video instructions (very helpful) and used others comments for removing the control panel. For the latter I used a small allen wrench to carefully wedge the bottom two indents (look from below panel edge) slightly up and forward to release the panel. Next, after removing the four screws, the assembly (housing shield) removed fairly easily. I then had full access to the flapper and removed this carefully with the pliers so as not to damage the piece it was attached to (Dispenser Door Recess Crank?). The rubber outer flange on the otherwise plastic flapper was very irregular for approx. 1/4 of the circumference and thus did not seal. So far it's been one week and no more frost build up or frozen water dispenser line.

Was this instruction helpful to you?

Customer:: Ronald J from Seabrook, SC
Parts Used:: WR17X11653
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Flapper door mis-shapened

Took the paper clip, pressed in through the holes on the bottom of the ice dispenser panel. Removed the four screws. Loosened the panel and removed the wires. replaced the flapper door. Then reversed the process. Your video was VERY helpful except for the paper clip. Had to get that off another web site.

Was this instruction helpful to you?

Customer:: Roy from Paso Robles, CA
Parts Used:: WR17X11653
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Ice Maker flapper

Your Video really made it easy, showing the actual replacment of the part. However I did have one problem, which was I could not unplug the panel just by pulling on the plugs. A locking catch is on each plug so I just moved the panel out of the way.

Was this instruction helpful to you?

Customer:: Lynwood from Spring, TX
Parts Used:: WR17X11653
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

flapper was curled at one edge allowing air to enter and causing frosting in the freezer

I followed a video supplied with the e-mail notification of the shipment of the part. This was one of the best experiences I have had with locating, purchasing and installing a replacement part for an appliance.

Was this instruction helpful to you?

Customer:: DON from ZELLWOOD, FL
Parts Used:: WR17X11653
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Ice Shute Flapper Was Distorted And Did Not Seal Opening Causing Frost Build Up

Removed control panel by inserting small screwdriver in the 3 holes underneath to loosen. Remove 4 screws holding circuit board . Unplugged 3 connectors. Removing circuit board gave access to flapper. Removed flapper by unclipping. Installed new flapper and reversed disassembly procedure. This was 2nd time in 2 years I had to replace this part.

Was this instruction helpful to you?

All Instructions for the TFX30PRYEAA