TFX25PABGAA General Electric Refrigerator - Instructions

It was way to ez to install only a couple of minutes that's it

Easy

took a little more effort than the video show to remove old module and replace new. Works fine now.

Unplug your refrigerator. Remove the shelves, light bulb shield and light bulb. Remove the two hex head screws to either side of the light bulb. Wiggle out the back panel. Locate the heater assembly hanging from the bottom of the coils secured with two screws. Remove both screws and lower out the heater. Unclip both connectors from either end of the heater. Take the new heater and replace both end clips. It only goes in one way, so you can't mix them up. Using the two screws, attach the new heater exactly like the original. Wiggle the back panel into place and replace the two hex screws. Put the light bulb and shield back in place and put back in the shelves. You are done.

checked web site for similar problems and said it was either the defrost heater or timer took my chances and went with the heater Its been 2 days and so far it seems to be working correctly if it happens again will change the timer Thank you for your help with this product couldn't be happier didn't have to have a repair man come would have been hundreds I am not a handy person but your site made it so easy

remove plastic top hinge cover then twoscrews holding door with door closed it rested against freezer door then lefted off door put on flat surface remove tow screws at bottom of door installed new cam

I started by replacing the defrost thermostat. I was wishfully thinking that would solve the problem, and I knew I would have to do it anyway (you have to remove it to test it, so, for nine bucks . . .). That was the hardest part of the job, because I am wide and the freezer is narrow. (PartSelect has a good instructional video.) A good wire stripping tool is worth the investment. My mistake (laziness) was not testing the defrost heater when I had the chance. It was shot, too. I quickly ascertained that it needed replacing (frost on the rear of the freezer; the original problem) and so I ordered one. The first one I got was defective. PartSelect over-nighted me a second one for no additional shipping. Installed it as soon as it arrived, a couple of weeks ago (it attaches very simply at the bottom of the rear of the freezer; two screws and plug-in wires). No problems since. Total cost, about $60 plus shipping. I can't even get a refrigerator repair guy to visit for less than that.

diagnoises said 49% thermostat replace preety easy did not fix so i took out defrost rube ran continuity test with showed bad unit ordered one here jn 2 days put in works great easy for me

Remove the back cover inside the freezer, with a hair dryer, defrost the frosts built up over the fringes, only the 4 sides of the back panel needs to be defrost so that I can get access to the heater and Thermostat. The heater is a tube like and if it looks black, it is bad, the new one is filled with aluminum coils inside the tube that you can see. Replaced the heater and everything worked. It has been fine for a week now.

Emptied the refrigerator door so it was easier to take off. Used a screwdriver to remove the screw on the top hinge. Lifted door off bottom hinge. Laid the door down so I could take the bottom hinge off. Removed worn out parts and placed the new one on. Slipped door back on hinge,made sure it would close properly and was lined up with freeze door. Put top hinge back in place. Done!! Now door finally shuts on its own again!!! EASY!!!

Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.

Remoed bottom hinge and replaced broken cam riser. Replaced Bottom hinge.

Removed two screws from the top hinge, two from the bottom - replace and put back together. It took longer to remove the food from the door than it did to replace it. THANKS

Emptied door shelves and removed top pivot hinge bracket. lifted door of lower pivot and set aside.

Removed vent-toe base and replaced hinge 'L' bracket and cam.
Removed two bolts from bottom of door and inserted new plastic cam.
Set door back on lower pin and re-attached top hinge bracket while aligning door.

Replaced articles back in door and watched it as it it self closed. Total time, less than 15 minutes excluding cleaning of equipment while dis-assembled.

Part Number: PS290199

1. Empty the door shelves.
2. Leave the door closed.
3. Remove the grill directly beneath the doors.
a. It snaps in. Pull simultaneously on the outside edge and the bottom about 2 inches in from the outside edge.
4. Using two people. One holding up on the bottom of the door. The other removes the two screws that hold the hinge to the refrigerator.
5. Open the door slowly and let it down slowly to pull the door away from the top hinge.
6. Replace the new hinge half on the bottom of the door. Insert the other half of the hinge into the hole of the door to keep the other half lined up while tightening the screws.
7. Apply a small amount of lithium grease to the contact surfaces of the new hinge.
8. Using two people. One person is to hold the door. Best if he/she holds it from the bottom. The second person lines up the top while pushing up on the door to insert to the top hinge.
9. Insert the other half of the new hinge into the bottom of the door.
10. Line up the holes and insert the two screws that hold the bottom hinge to the refrigerator.
11. Reinstall the grill.