TPS24PBBBBS General Electric Refrigerator - Instructions

Separately (from a different site) purchased new compressor fan and motor. I purchased the grommets here because the other site listed the grommets as temporarily out of stock. I did watch one of the videos on PartSelect about the grommet replacement. Repair was pretty simple, biggest challenge was getting to the screw on the far side of the motor. Removed the two screws holding the fan motor into place. Removed motor and blade. Reinstalled with new fan blade, new grommet and new motor.

Part attaches to metal plate near crushing fingers which attaches to ice holding bin. Remove about 6 screws total on each side of plate. You must disassemble the auger & other parts so you can reassemble it in the proper order. Not many parts but i always take pics to cut down on time. New part is at the other end of the auger and acts as the holde of the auger shaft. Picture a crankshaft with a bearing on each end so the auger rotates between new part and the other end of auger shaft. That's it.

Part was perfect fit .Removed fan .three screws.replaced that s it

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

There are Great videos on YouTube!!! Turned off power,Removed trim ring, Pushed a philips head screwdriver in one of the holes underneath the electrical panel with the selector push buttons. This releases the electrical panel. There are Three wire sets with plugs. I removed the plugs and took the electrical panel out. Removed four Phillips head screws and pulled out the big paddle switch. This then exposes the flapper. Replaced flapper with new one and reassembled everything. When I had everything apart, I cleaned with window cleaner. It was pretty moldy from the water leaking. Turned power back on and tested everything to make sure I didn't mess anything up. Works great

Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.

I just followed the instructions on the video and it was exactly as they said......no surprises.

Replaced dispenser door flapper by following the do it yourself video in this site. It was really easy. Just be careful when removing the dispenser black bezel. I broke one of the little tabs when taking it off.

Replaced flapper. Followed the video. The lamp caused the removable plastic bracket (which supports the control panel and the ice chute) to fuse with the plastic frame in the door. Eventually broke the fused plastic, removed the bracket, and filed the rough broken plastic before reassembly.

Take a thin flathead screwdriver (or metal spatula) to separate the lower molded strip from the handle. Once removed, I discovered two small screws that secure the bottom of the main handle were loose. The head of the screws had five points which required a special drill bit that I had in my tool box. The screws were tightened allowing me to align the replacement Tail strip and snap it in place. Some pressure is needed to secure it to the door. Once you hear the inserts "snap", then check for any open spaces between the strip sides and the door. If none, you're done!

Use small putty knife to cut internal sealant on ice maker door trim piece. Then you can easily remove it.

Had to defrost the freezer to melt off all the ice before servicing. Once that was done the icemaker replacement only took about 15-30 minutes to complete. The new icemaker came with many accessories and adaptors that were not needed and the instructions were based on replacing an older model and not really clear for my model. They mentioned not being able to use the new stripper but it was exactly the same as the old one so I left the new one in place. All in all it was easy and did the job.

I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.

Remove front cover did not remove wires remove ice and water unit took off flapper put new one on 5 minutes back together

It took me longer to remove all the shelving than it did to replace the part, at first I had a small short, [a bare wire was open, cut off too much casing,] thought it was faulty, but I cut back on the wire, wire caped it, then taped it with electrical tape, reinstalled, workes just fine now, at temp #6on dial. should have paid " MORE ATTENTION TO STEVE". I would highly recommend [ PARTS SELECT] TO ANYONE WHO NEEDS A PART, IF you pay attention to the video, you will find it not too difficult to repair.
Mr. PAUL KLUGH [KLU] THANK you PARTS SELECT. PS THEY would have replaced the part if need be.