GSA20IBMDFWW General Electric Refrigerator - Instructions

My Ge top freezer fefrigerator was going into defrost mode and the heater was staying on for too long causing the food to thaw and eventually refreeze. Originally thought it was the mother board but after researching and do some troubleshooting of my own I realized the defrost terminating thermostat was bad. $8 part from Parts Select. Accessed the evaporator by removing back wall plate. Located thermostat and cut two lead wires to it. Spliced in new thermostat and reattached to eveaporator. Refrigerator seems to be good as new. There is an installation video on the web page that shows you step by step proceedure.

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

I followed instructions posted by experts and hands-on experienced owners on PARTS SELECT.Very helpful! Repairs was easy!.Defrost thermostat tried first,unsuccessfull then the DEFROST HEATER HARNESS next :BINGO !. Thank you PARTS SELECT ! Thank You every ones who posted their successful experiences that gave me confidence.From now on I know I can count on PARTS SELECT and its sites to solve my future headaches!

Located temperature sensor on condenser in the freezer section( as per instructional video ). Cut off bad sensor with wire cutter then soldered on the new sensor and sealed with electrical shrink wrap.

as per video- follow all of the videos and u r going to save a lot of money tx partselect im glad I found u guys ps only order from partselect.com they only ship the correct parts remember look at the video select the symptom and buy as per video tx again problemsolved

I identified the noise was coming from the coils / and the fan. Cleaning the fan helped reduce the noise a bit but it still kept recurring. I ordered the part, which was really easy using the diagram on the website. The instructions and the video were really helpful and was able to remove the old motor and replace it with the new one with relative ease. While there I cleaned the fan blade and vacuumed the surrounding area. This whole repair went quite smoothly and has given me the confidence to take on other repairs before calling out the repairman.

Repair was rather simple. Removed the appropriate shelves and to make it easy to get to. Removed the ice container. I had to remove several items to get to the evaporator fan. Removed the ice dispenser motor cover, air duct cover, and the evaporator orifice cover. After all was removed the fan assembly was still attached to the orifice cover by the evaporator fan bracket. Remove bracket to remove the fan motor and assembly. Replace the all the old parts with the new and start the reassembly process. Really the only difficult part was working in such a small area. Good luck.

I had already replaced the icemaker and solenoid valve and had not solved my problem. After I looked at the back wall gasket, it was obvious that the element was getting too hot. Installation was really simple- unplug refrigerator cord, remove frozen food and racks, remove light cover and back sheet metal by removing 4 screws, cut and splice wires to new parts. Reinstall.

Using a nut driver, I removed the panel that covers the freezer coil. Using wire stripper/cutters. I replace the Temperature sensor and Thermostat. I also replaced the heater element that comes on when the freezer goes into defrost mode. Worked like a charm. The original problem was the freezer compartment would thaw just enough to start the melting process then freeze everything and build up ice to the point where the ice that was produced from the ice maker would just turn into a big block of ice. Everything is working perfectly now with only an hours worth of work and about $75.00 in parts.

I followed the step by step instructions on provided by Part Select. I replaced the coil heater and temperature switch.

We watched the how to install videos online then installed the new parts. Quick easy and now our freezer is defrosting like it should. Thanks Parts Select.

I replaced both the Defrost Thermostat and the Temperature Sensor located on the top of the cooling coils. I ordered them because they were the least expensive items that addressed my problem. They did not correct my problem. I then ordered the Main Control circuit board. I installed the board in about 15 minutes. Finally my freezer returned to the set temperature of 0 degrees F. Problem solved

Just like the video show on the wed site.

Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold

Really easy unplugged unit took off back panel in the freezer thawed out coils remover sensor replaced with the new one put the unit back together works fine took about 35 min.