TCX18IACCRAA General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Travis from North Quincy, MA
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old end cap broke.
Put the new end cap on and snapped it into place, took about 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Northglenn, CO
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The above door End Cap broke.
The repair just required snapping the new part on to the door shelf and then snapping the shelf in to the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from New Milford, NJ
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cap on the door retainer bar broke.
The replacement cap fit perfectly. Unfortunately when the orinigal cap broke it tookout a small piece of the surrounding plastic leaving nothing for the new cap to catch. I have the piece and tried several kinds of glue but nothing holds it securely enough. I would however readily recommend your company. The service was terrific.
Thank you.
Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruchik from Bronx, NY
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf retainer bar end cap.
I ordered 2 end caps just to keep one as spare. Turned out I had ordered a size larger than the one already on the refrigerator. So I replaced both ends and it worked fine - with increased shelf space. Now I can even fit a gallon container with ease!!! Took about 20 seconds. I just wish there was an easier way to measure parts before ordering. Otherwise, the entire process from order to finish took about 3 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from PRESQUE ISLE, ME
- Parts Used:
- WR2X9296
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken shelf end caps- right side of 2 shelves.
After watching video I took off end shelf caps. It took close to 10 mins to replace them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sammy from Farmington, NM
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastic parts that hold the brackett to the shelf were broken.
The part just snapped into the shelf bar. Extremely easy to fix. Since you show the part in a grid I was able to tell, by holding my old piece up to the screen, that the new part would be the correct size. We have rentals and are always needing parts for appliances. Impossible to find locally.
Also the part came so quickly it was almost as good as buying it here in town. Thanks. Donna Bingham
Also the part came so quickly it was almost as good as buying it here in town. Thanks. Donna Bingham
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from E LONGMEADOW, MA
- Parts Used:
- WD2X5166
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
water leaking from under dishwasher
Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.
Indeed, inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.
A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Indeed, inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.
A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SAN DIEGO, CA
- Parts Used:
- WR2X9162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My freezer door had a retainer bar that became disconnected at one end because the coupling broke.
I slipped the coupling over the bar and then into a door slot. It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erika from Joliet, IL
- Parts Used:
- WR2X9296
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door shelf clip had broken
This shelf has been broken for about a year now and my husband tried several little quick fixes that would work for a while and then the shelf would fall again. A quick search online led me to your website, the part arrive within two days, and the shelf was fixed in less than ten minutes. It's working great. We'll definitely keep you in mind for the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stan from Dallas, TX
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door shelf bar holder
I ordered the part before noon and I they had it out the door and in my hands within 24 hours! It took about 2 minutes to take out the broken part and snap in the new one!Great service and easy install!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John D from Chevy Chase, MD
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
This part broke for whatever reason, I do not know.
I needed a pliers to extract the shelf reatainer from its place in the door of the fridge.
I found the part in the partSelect catalog, ordered it, opened the box, and snapped the replacement part into place. I then popped the Shelf retainer back into place where it belonged.
Piece of cake.
I found the part in the partSelect catalog, ordered it, opened the box, and snapped the replacement part into place. I then popped the Shelf retainer back into place where it belonged.
Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Clayton, NY
- Parts Used:
- WR2X9296
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The retainer latch broke
Removed the shelf retainer and snapped the new one in. and reinstalled the shelf on the door.
This was a very simple problem!
What really impressed me was that I ordered the part from you before noon on one day and received it by 11 AM the next day!!!
This was a very simple problem!
What really impressed me was that I ordered the part from you before noon on one day and received it by 11 AM the next day!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Prescott, AZ
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken door shelf retainer
Just replace end cap and install. The beauty of this was the door was broken in the evening before July 4 when all retail had closed down early for the 4th weekend. I hit Part Select on the computer, scrolled down the partslist,looked at pictures and figured out from that the necessary piece I needed, hit the buy button and in less than 10 minutes had an order placed. July 7 UPS was at the door with the parts and my reefer was back in business. NO service call and no extra charges!!! Thank You, PartSelect!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheryl from Wyoming, MI
- Parts Used:
- WR2X9296
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door shelf retainer broke off
First, I removed the broken end cap from refrigerator door. Then I snapped the new end cap into place. Repair took less than 5 minutes and required NO TOOLS! Easy!! Got my part in one day, Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Miranda from Waterford, CT
- Parts Used:
- WR2X9296
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The end cap on the door shelf snapped off.
I pulled off the broken piece, ordered the new piece, and snapped it on. VERY SIMPLE.
Was this instruction helpful to you?
Thank you for voting!