TFK22JABBAA General Electric Refrigerator - Instructions

I can not find the bill therefore I do not know what part I installed, as I keep installing parts in my home. I believe you are referring to a Vegetable Bin of my GE Refrigerator and you do not have to be a rocket scientist to install a new one.

Sorry
Abraham Zighelboim
PS: I just saw that was the Veg Bean

This is a side by side freezer/refrigerator, nearly 30 years old. The repair was very quick and easy. 1. Remove two screws from top bracket. There is no cover for the top hinge on this older model. (2) Lift off door and set on kitchen table. (3) Remove two screws holding bottom door hinge. (4) remove two screws hold the cam and shims on the bottom of the door. (5) replace the broken cam on the door, and the bottom hinge assembly. (6) Replace the door on the bottom hinge. (7) Re-attach the top hinge screws, making sure the door is parallel to the freezer door. It took about 10 minutes to do all of the above. Best yet, I ordered the kit about 10am on a Monday, and the parts arrived, normal delivery, before noon the next day.PS- I used petroleum jelly to grease the hinge before replacing the door. The only tool I needed was a nutdriver.

I removed the lower cover plate and placed a small scissor jack (used my car jack) under the refrigerator door, loosened the upper hinge, slightly raised jack to take the weight off of the lower hinge, removed the hinge with a 5/16 nut driver and the cam with a 5/16 socket. Installed new hinge and cam, removed door support and secured top hinge, check operation. Worked GREAT, did not have to remove door.

I viewed a how-to video on partselect.com. I removed all items from the door shelves. Used a screw driver to remove the top "hinge" plate. Used a nutdriver to remove the door hinge plate. Removed door, laid on it's side-hinge side up (if you don't have a helper, lay it on a flat service). Simply removed the broken bottom plate and replaced with new part, and reinstalled on refrigerator. Super Simple!

Followed the u tube video that was on the Part select website. Very easy install when following the video.

Did the repair jut like the instructions on the web site stated. There was a good video for doing this repair. Looked at it a couple of times and did the repair right off the bat. Thanks folks.

replace the lower door hinge assy. and closer cam as a set.Only used a 1/4" socket and ratchet.The process was very easy without any problems.

Pull out old pan,remove the vent cover from front and install it on the new pan, done.

removed door, replaced hinge, replaced door.

Part was received quickly and quickly installed-Thank you

Removed top hinge cover and screws. Lifted door off bottom hinge and replaced bottom hinge assembly.

-empty door of food - remove top hinge-open door and lift upward-remove lower hinge assembly-add new part to lower hinge assembly- put door back on lower hinge pivot- close door line up door parallel with other door- replace upper hinge

First I watched the video and everything on that video was correct. I took off the hinge cap with a Philips screw driver on the top of the refrigerator. Then I took out two 5/16" screws with a socket wrench. Removed the hinge and the door lifted off. On the bottom of the door took out one screw and loosened the other one and replaced the Cam Riser. Put everything back together and it worked perfectly.

I blocked the bottom of the door(CAREFULLY!!) in position to elevate the door & take strain off the lower hinge & pivot post, while maintaining proper door alignment. I removed the two screws holding the hinge & post assembly from the frame, saving the screws & spacer for reuse. I removed the two screws holding the upper cam bracket on the door, again keeping the attaching parts. I installed and carefully aligned the new cam, original spacer & retaining plate to the lower edge of the door. I installed the new hinge & post assembly using the existing spacer & screws. I aligned the door & seal while checking the gap from top to bottom and from side to side. I carefully tighten the screws and rechecked the gap between the door & frame as well as the alignemnt of the door seal. Once satisfied with the alignment, I finished tightening the screws. I emphasize care and extreme caution in reinstalling the screws, they are a self-tapping (self-threading) type of fastener and this requires caution to make sure they are started and installed in the original threads of the door & frame. I put them all in using only finger pressure until I was positive they were started straight, going into the original threads, NOT trying to cross-thread or cut new threads, the structure is too thin for that and stripped threads will result! The door alignment and gap spacing is critical, make sure to check these adjustments carefully to ensure proper operation. Total time of repair, less than 15 minutes. I hope I have not over-simplified this because I have over 55 years of Automotive shop experienced and an ASE Certified Master Auto & Truck Technician...:-)

Set up two saw horses to put door on. Unloaded door shelves. removed upper hinge, and lifted door from lower hinge, placed door on horses. changed lower hinge on refrigerator. put door back on lower hinge, and closed door. Put upper hinge back on. Reloaded door shelves. It took more time to Unload, and Load door shelves than to replace Hinge.