GTG25DBSARWW General Electric Refrigerator - Instructions

Very limited working space in this model. Must remove grill and disconnect elect connector on motor. One additiional tool suggested: Extendable rod with magnet on end because you will most likely drop something. First, remove two screws holding motor to metal strap. Tool must be inserted between blades of fan in order to get to the screws and this is the hard part. Fan and motor are removed as one assy and this takes some manuvering. Might have to remove front screw on metal strap to gain more room. I did not attempt to remove fan shroud. My fan was attached to the motor shaft with a metal clip. Spray a good lubricant such as PB Blaster on the shaft, wait a few minutes and press it or tap it out gently. Save misc parts on old motor for reassembly. Your set up may be different so check out everything before starting.

Part select was great. I entered the model number and was able to locate a list of problems associated with my refrigerator. I was able to view a repair video, courtesy of part select. I followed the instructions and the repair was simple. The hard part was trying to remember how everything went back together. I unplugged the unit and removed the freezer racks. I then unscrewed the back panel within the unit. I then placed an old towel inside the unit and used a hair dryer to melt the ice build up inside. I also removed the light bulb and then removed ice maker. I then located the old defrost thermostat and replaced it as demonstrated in the video. I then located temp sensor and replaced it. It took longer trying to secure the rear panels than the actual repair. My mistake was I had secured the ice maker unit before securing the fan panel. I would secure the large panel first, then followed by the light bulb/fan panel. The ice maker should go in last. It has been 8 days since the repair and it still working! The total cost was $27.

first unplug unit then pulled the inside back freezer cover off piled towels around and defrosted the the unit thoroughly. located the defroster unit tested for continuity was good so i replaced the temp sensors they were just nip off the old one and splice in the new one. also replace the defroster thermostat was the same nip and splice. *the parts shop did not find the model #i have but knowing those parts are interchangeable with all G-E models i ordered the parts

I looked at your video . very nice. job went fast. thank you mike.

I watched the video then ordered the defrost timer it was here in two days (ordered late saturday arrived tuesday). Spent $. 16 On two wire nuts and went to work . The repair took one hour including defrosting the coils with a hair dryer . Your website is my " go too " for parts and repair. I spent less than $20 including shipping !

What an awesome site! After putting in my model number and finding the problem I was having, I simply picked the 2 parts that were most likely to solve the problem. I bought a defrost thermostat, and defrost heater. To a high certainty, they would solve my problem. They didn't however! I ended up having to buy a temperature sensor on another order a few weeks later when the problem resurfaced! My own fault. I should have bought it the first time. As others have written: the longest part of the job is defrosting the ice from the coil. One thing I did that I didn't see suggested: plug the drain hole below the coil. I put a couple towels in the bottom of the freezer and ran the hair dryer. Didn't take long. I read that the amount of water created will overflow the pan under the refrigerator, so I plugged the drain hole. Once you clean that mess up, the repair is pretty straight forward. Great site. Even through I had to make two separate purchases, I still saved a lot of money. Thanks!

According to PartSelect website, the probably cause was Temperature Sensor or Defrost Thermostat. I watched the replacement videos. . .. very nice and seemed easy. Ordered the parts and got within 3 days (nice!). I followed the procedure on the video for disassembly, I used a hair dryer to melt the ice buildup on coils and then cut the old Sensor and Thermostat out of the wire harness and, instead of using crimper to seal my new splices, I soldered them instead. I used shrink wrap sleeves, then wrapped in electrical tape for permanent insulation. My Fridge now functions like new again.Thanks Partselect! You are the best!

Emptied Freezer (to get access to panel covering condensor coils and Defrost Thermostat). Pulled off cover panesl. Had to wait for ice to clear from condensor. Replaced Defrost Thermostat (5 min job), replaced panels and was back in business.

removed evaporator coil cover inside freezer, defrosted the coil with blow dryer, cut wires to defrost thermostat, removed old defrost thermostat, wired new one to old wires with wire nuts and then taped with black electrical tape, reattached defrost thremostat to evaporator coil, easy job, the thing that took the longest was thawing out all the ice

Replaced the Defrost Thermostat and the Defrost Heater.

I looked at the video that came with the part and followed what i saw. My wife and i was about to go out and spend between $1500 and $2500 on a new refrigerator due to continuous defrosting. It had been happening for about a year. I followed the instructions from the video and the defrosting has stopped. Thanks so much for the video and the part! We do not need a new refrigerator after all.

Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold

1.- ordered the thermostat replacement.2.- unplugged unit 3.- empty unit, removed racks too(freezer only) 4.- used a hot hair dryer to melt the ice,kept drying water inside the unit. 5.-used electrical pliers carefully removed damage thermostat.6.- putted on new thermostat, used standard wire connectors to keep wires together and wrapped them with black electrical tape. 7.-gentle replaced thermostat back in contact with the other pieces.8.- returned back racks and all removed pieces,drying all water from melted ice.9.- plugged it,...done

I had already replaced the icemaker and solenoid valve and had not solved my problem. After I looked at the back wall gasket, it was obvious that the element was getting too hot. Installation was really simple- unplug refrigerator cord, remove frozen food and racks, remove light cover and back sheet metal by removing 4 screws, cut and splice wires to new parts. Reinstall.

Just like the video show on the wed site.