GSG20IBMCFBB General Electric Refrigerator - Instructions

Refrigerator was showing actual temperature of 80 deg, freezer was about 3 deg high. (house temp was 65 at the time) Defrost heater seemed like the only component able to heat that much, so the defrost thermostat seemed like the likely culprit. I followed the installation directions in the video, and the fridge has been fine ever since.

I took off the back panel in the freezer. Located the wires going to the old thermostat, cut them with wire cutters. I then spliced the matching wires together and attached the part to the coil tube (There is a little clip on the part, be sure to do this because I forgot and had to go back and do this again!!!).

All the rest of everyone's post are all what I did. The only other thing I recommend is to put the back panel over the evaporator coils when your done. I replaced defrost thermostat, and heater. Once I initially completed it it kept icing over more than usual. You have to put the back panel back on so airflow goes over the coils.

My Ge top freezer fefrigerator was going into defrost mode and the heater was staying on for too long causing the food to thaw and eventually refreeze. Originally thought it was the mother board but after researching and do some troubleshooting of my own I realized the defrost terminating thermostat was bad. $8 part from Parts Select. Accessed the evaporator by removing back wall plate. Located thermostat and cut two lead wires to it. Spliced in new thermostat and reattached to eveaporator. Refrigerator seems to be good as new. There is an installation video on the web page that shows you step by step proceedure.

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

Replaced top sensor in ref. and top sensor in freezer as well as defrost thermostat - works as advertised - easy fix, saved a bundle thanks to this site! Parts ordered and shipped quickly and without complications!

I followed instructions posted by experts and hands-on experienced owners on PARTS SELECT.Very helpful! Repairs was easy!.Defrost thermostat tried first,unsuccessfull then the DEFROST HEATER HARNESS next :BINGO !. Thank you PARTS SELECT ! Thank You every ones who posted their successful experiences that gave me confidence.From now on I know I can count on PARTS SELECT and its sites to solve my future headaches!

We used partselect troubleshooting appilication to figure out what was most likely causing the problem and what part would fix it. The suggested part was the freezer's defrost thermostat and the probability that this would fix it was 52%! The diagnosis made sense because when we emptied the freezer to see the part, the coils were frozen solid with a thick layer of ice. We thawed the ice and the refrigerator worked fine for a day and a half at which point the ice was back and the refrigerator was warm again. We ordered the part. It came in 2 days. We snipped two wires and removed the old part, twisted the wires of the new one in place, taped it up and it worked! Fast, easy, cheep! $8 For the part, about the same for shipping and no $70 service call. Selectparts is bookmarked for "house repair"!

as per video- follow all of the videos and u r going to save a lot of money tx partselect im glad I found u guys ps only order from partselect.com they only ship the correct parts remember look at the video select the symptom and buy as per video tx again problemsolved

killed power-gently pried out old switch using two screw drivers-replaced faulty switch-and tested OK.

I decided to replace motor and fan, having previously altered/trimmed the fan which stopped the howling but caused a vibration. Unplug from mains. Clear out two top shelves in freezer. Remove light cover. Remove two screws(1/4 driver)at top of steel panel in rear of compartment and let it drop. Remove two screws above light. Pry up section above light/fan housing to access two screws retaining the light/fan assembly, loosen screws sufficiently so that assembly can be lifted and removed. Disconnect wiring plug by pinching in the sides of the plug and pulling out. Pull fan off motor shaft. Remove two screws clamping motor. Cut cable tie and molded wiring grommet to free wiring. The existing light wires can be removed from the old plug by carefully cutting around the old plug to free the pins and then pushing the pins into the new plug. Reverse procedure to assemble.

After on two occessions from a refrigeration man who did not fix it I decided to work on it myself. Knowing it was not the overload relay or capacitor I changed the temperature control board but without success, next I took the main control biard, located on the back lower left off for inspection and found that there was a contact terminal on one of the relays melted, after resouldering contact I reinstaled the board and then plug back my refrigerator into the outlet and there it goes like brand new. It was quite easy and quick to do because the board has precisely matching plug-in-terminal wiring harness, for diconnect and reconnect, very smart way. To remove cover for access, take board off, fix and replace, it took me aproxmately fifteen minuites, only using a quarter inch stud driver. Great way. So thrust yourself and save some $Bucks. Reynold.

I followed the video instructions online and the job went very smoothly. Unfortunately, the problem is still occuring [this of couse is no fault of yours] there must be another problem to remedy. Really appreciate the videoThanks Parts Select for excellent product and quick delivery

The replacement went very well. The video was not just as the unit I have but with a little work I worked it out. The service was very good. I received the part in 1 Day. Thanks for the good info. Keep up the good work regarding the videos. This helped. Just for the info. I did a post mortem of the switch. The strain of the wires pulling on the switch caused the failure of the switch. The design of the old temp switch was bad and workmanship was very poor in the original box. Thanks again Ron

Removed the back pannel from inside the freezer. Defrosted the ice build up. Removed the shroud from the back top of the freezer. ( This contains the fan and the light assembly). Removed the fan and replaced the motor. Cut the wire for the temperature sensor and wired in the new one. removed the defrost thermostat and replaced with the new one. Reassembled the unit and reinstalled it into the freezer compartment. replaced the pannel and plugged unit back in.