TPG24PFCCWW General Electric Refrigerator - Instructions

The video on the site was very helpful. The repair was really easy. It was exactly the way the video showed how to do it. I would definitely use this site again to find parts, figure out the "how-to", and use for skematics of appliances. Thanks.

turn off water. turn off electricity. empty freezer section of frozen food. remove ice bucket. loosen two screws holding IM to wall of refrigerator. lift off icemaker, and then unplug it as you remove it. INSTALL new IM by: putting new water funnel onto new IM. attaching adapter cord to IM. plug in IM electrical cord to refrigerator and then hang the new IM onto the two loosened screws on the refrig wall. Now tighten the two screws. the extra adapter electrical cord hangs below the new IM, but does not get in the way when you reinstall old ice bucket. reload food, turn on elec and water. PS. i had a crack in the casing of the new IM, so i got a new one, but that one was cracked too. so i just installed the second cracked one. hope it is not a problem.

Watched video on website then removed old ice maker. New one went in without any problems. Working great. I am a 60 year old woman and had never done anything like this but so easy. Husband scared now, doesn't know what project I will take on next.

REplaced old icemaker with a new one. Install simple, However that was not the problem. I then replaced the water valve. Still no ice. I check the electric connection was OK. THe problem was the elbow fitting on the top back of the refrigerater leading to the icemaker was blocked with ice.Cleared it and turned water faucet up all the way. Ice maker worked.

The instruction video was great, mine was easy than even the video showed it to be. I changed it out in less than 15 minutes and it works great. The niocve things I didn't have to wait for a repairman or my husband to fix the problem.

Placed the glass shelf in the new shelf frame and the frame in the refrigerator.

I was unable to positively identify the replacement shelf frame on the GE web site. Part Select's exploded view made it a piece of cake!

remove the 'pop-out " frame around the door recess, you pry the flexable seal from around the ice despenser, have someone hold the unit with the wiring, remove the one screw that holds the door recess, and replace the new one. reverse the procedure. remember to unplug thr frig. first

install icemaker water was allways delivered to previous unit water is not being delivered to icemaker still having difficulty

really simple,take 2 nuts loose pull the hose out and then replace.took less than 30 minutes

Removed old ice maker, then screwed in new ice maker. Only thing that was a little difficult was to hold the auger motor, while trying to unplug the clipped in plug on the old ice maker. I could have used an extra pair of hands.

Instructions that came with the part were useless. I would have created new problems if I had attempted to follow the instructions. However, once I had the old part removed and put it beside the new part, required repair process was obvious, easy and quick. Frig now makes ice better than it ever did.

Followed the instructions. Smooth as silk. This part is better than the original. There appears to be a sensor that beeps when the ice reservoir is full.

I spent 15 - 20 minutes just hunting/deciding which of several sets of parts & directions to follow. The provided directions were not bad; but none of them quite matched my GE ADORA side-by-side model. Once I came up with the actions I would need to take...I was done in 5 minutes! The kit , as I said, came with all the parts one could need (and one or two un-needed parts included for other model GE refrigerators) I am very happy with PART SELECT...altough GE doesn't rate as high with me for their declining reliability.

I followed a video supplied with the e-mail notification of the shipment of the part. This was one of the best experiences I have had with locating, purchasing and installing a replacement part for an appliance.

Snapped off the plastic plate covering the dispenser. Removed the four screws holding the mechanism in place. Remove the electrical connections. Pull the mechanism out and up carefully pulling the dispenser pad out with all the mechanism in place. Look at the mechanism before removing any parts to get a mental image so that reassembly will be easy. Remove any electrical switch or circuit boards and remove old parts before submerging the mechanism in hot soapy water for clean-up. The Clean-up will take longer than the disassemble and reassembling. After completion the dispenser works as it should.