PDS22SBSALSS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Severna park, MD
- Parts Used:
- WR14X10177
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Seal on freezer. Broken
Cleaned mating surfaces with acetone using vapor mask because done indoors. No instructions as to which cleaner to clean old glue off. Matting surfaces. No nistructions as to what glue to use so used silicone. We'll see if it holds up
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Hopewell Junction, NY
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Fridge/Freezer bad temps and clicking sounds from rear
Found out via searches that the most likely failed part was the Main Control Board. A simple repair with basic tools and a HUGE savings. Thanks to everyone here for the posts.
PS - on my particular GE model PFS22SISBSS there was no need to cut any wires as per the instructions because the wires did not exist on this unit.
PS - on my particular GE model PFS22SISBSS there was no need to cut any wires as per the instructions because the wires did not exist on this unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- QUOC-LOC from LYNN HAVEN, FL
- Parts Used:
- WR55X24064
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The control board generated clicking noise. Temperature display wrong values.
On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trevor from Brooklyn, NY
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
Refrigerator failed to get cold.
the new board was more complicated than the old, however the install instructions seem to have anticipated this. It works for mow. thanks for inquiring'
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from Middletown, DE
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
refrigerator clicking noise
removed cover from rear of refrigerator. disconnect mother board connections. Unplug first, used needle nose pliers to squeeze plastic tabs holding on motherboard and replaced old with new and plugged back in connections. Plug back in refrigerator and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lisa from houston, TX
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Refrigerator kept turning off and on
I easily removed the screws and then removed the board and took a picture so I would remember how to re-connect it. It was really easy and now my refrigerator is working great. If I can do it anyone can do it. My husband was amazed that I did it all by myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alicia from Nutley, NJ
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer and frige stopped getting cold. had repairman come to check . thought it might be the board but wasn't sure (not very helpful). afer replacing board it took o time to get cold. no problem since.
very easy repair, simple exchange
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Floral Park, NY
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
first water on door would shut off then refridgerator shut down completly unpluged and pluged back in and it made clicking noise the light always stayed on
was not home when part came so my wife installed it enough said
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Newbury, OH
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Freezer fan made a howling sound
Used 1/4 nut driver and drill to take off acc pnl. The repair amounted to unplugging several connectors, removing the old motherboard, installing the new board and reconnecting the wires. this solved the problem and the whole appliance seems to run better.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from Sierra Vista, AZ
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Fridge failed to cool
Moved fridge out from wall. Unplugged. Removed circuitboard cover 6 screws?). Replaced circuit board (showed burn spots on back side). Replaced cover and plugged back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- larry from divernon, IL
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the refrigerator quit completely
I pulled the fridge out away from the wall, unplugged fridge, and found the panel that the main control board was behind. after comparing old board with the new i unpluged all of the connections unscrewed four screws and installed new board in reverse order. very simple..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Kearney, MO
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
no ice no water coming out of door and started making a clicking noise
I read other reviews then decided it was my main control board.Watched the video for install. It was easy to change out.Everything is working great again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Delbarton, WV
- Parts Used:
- WR55X10942C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Clicking noise while trying to turn on,would not turn on.
I checked the problems others were having to see if they had simular ones. They were having the same clicking noise I was having. My refrigerator would not turn on. Clicking noise but would not start. They replaced the motherboard. I searched the internet for prices. Part select was about $30.00 cheaper that the other stores. I ordered from part select. Nice helpful people to deal with. I installed the part in about 5 minutes, very easy repair. They sent me an updated part. Thanks everybody and Part Select for your help.
Was this instruction helpful to you?
Thank you for voting!