GSA20IBPAFWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sumlorq from Cleveland, OH
- Parts Used:
- WR23X10725
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light switch freezer door
put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Reston, VA
- Parts Used:
- WR50X10068
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Heavy frosting/icing in freezer
Replaced both the Defrost Thermostat and Defrost Heating Element. The You Tube repair video clips were extremely helpful for both operations. My difficulty was getting access to the parts that needed to be replaced in a very tight side by side freezer space. Otherwise, the repair went smoothly and the refrigerator is back in normal operation in time to save the perishable food inside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter M. from Lincoln Park, NJ
- Parts Used:
- WR02X10540
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Defroster fan burned up
First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Millard from Lavonia, GA
- Parts Used:
- WR72X240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The original part had a flaw in the attachement area allowing the rail to totally break away from the rear screw. I needed to get the new part and replace the old one.
First I removed the two screws that held the old slide to the refer side wall, (after unloading the shelf and taking out the Veg. draw). I then put the screws in the new slide spots and screwed them into the refer wall using a hand screwdriver (phillips) and put everything back in place. It was about as simple a repair of anything I have had in the past 75 years. I didn't even have to swear.
Was this instruction helpful to you?
Thank you for voting!
To much beer in the bottom of fridge and to much vegetables shoved in the middle drawer
Removed the two drawers. Unscrewed the side rails that cracked away from the screws.Replaced the new side rails in place screwed in the screws and waalaa all done....easy as pie. Oh by the way I am a woman with little experience of tools...Just have to say the pictures of the parts made it really easy to pick out the correct part. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Fresno, CA
- Parts Used:
- WR72X240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken right rail
First take all your junk off the shelf (with the broken rail of course), take the glass shelf off. Remove screws (phillips). Throw away old rail. Replace new rail, tighten screws. Replace shelf, replace junk. You're done.
Was this instruction helpful to you?
Thank you for voting!
Rails on crisper drawers broke. Drawers were crooked and difficult to open and close. Lived with this for TWO YEARS!
Removed each drawer and removed two screws for each rail. Disposed of old rails. Installed new ones using the screws removed from old rails. Put drawers back in and VOILA! Crisper drawers that work! AMEN PARTSELECT!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcia from Rifle, CO
- Parts Used:
- WR72X239
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
left drawer slide broke off at screw
removed drawer, unscrewed old slide, screwed on new slide, voila! finished! I was very pleased with PartSelect -- ordering was easy, the correct part came quickly, and packaged very well. All of life should work so smoothly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Dansville, NY
- Parts Used:
- WR72X240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
crisper drawer would not stay in place on right side
I removed food from shelf over crisper drawer, then removed shelf and crisper drawer, removed two phillips head screws in right side rail and replaced rail.
Easy as 1-2-3
Easy as 1-2-3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amanda from Plainfield, IL
- Parts Used:
- WR72X240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Slide rail cracked and eventually fell off
This was so easy! I got the part number off of the broken part, ordered online, and it was delivered the next day!!! So fast! Then I just unscrewed the broken part and reused the existing screws to install the new one. It took about 5 min.
Thanks for making everything so fast and easy!
Thanks for making everything so fast and easy!
Was this instruction helpful to you?
Thank you for voting!
no problems
I removed the screws and replaced the rails one at a time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from BENSON, NC
- Parts Used:
- WR72X239
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drawer Slide Rail - left side broken
Took the drawer out, unscrewed 2 screws, replaced the part, put the drawer back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dodly from Pembroke Pines, FL
- Parts Used:
- WR72X240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My old drawer side rail was broken
I removed the two screws from the old broken rail using a regular star screw driver and replaced the new rail you sent us. Took only 2 mints to do all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darlene from Downingtown, PA
- Parts Used:
- WR72X240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drawer Slide Broke
The drawer slide broke and I just removed the 2 screws that were still in the side of the refrigerator. I then screwed the new drawer slide in the same holes and it was done!! Simple, simple....even for me, the housewife.... ; )
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Allen, TX
- Parts Used:
- WR50X10068
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Fridge not cooling, freezer not defrosting
Must have spent 10+ hours solid looking up info on the internet. Our ice maker had broken years ago, the door flap had broken years ago and I thought this was the end of a fridge after just 6 years 8 months.
GE offered a "broken appliance" warranty for $379 for one year, with no guarantee that when a technician came to look at it, the repairs would be covered by the warranty!!! No thank you, you just want me to buy a new fridge. Okay, challenge on, I'll fix it myself.
I took everything from the back of the freezer out. Spent an hour defrosting (note: use hair dryer next time). Ruled out a motherboard problem (even though it appears I have the old style motherboard), removed dust build up from fan intake. I could not get the heater to come on, so I cut off the thermostat defroster and connected the wires together. The only way to get the heater on was to set the freezer control to 0 / zero.
So, ordered part from partselect.com and it arrived the next day!!!. Installed and unit appears to be defrosting okay after a week.
So now I'm back to order the ice maker part. The door flap will wait for another time.
Note: I've put in the time for novices and recognizing how the freezer is constructed.
Time includes taking everything out of the freezer section, unscrewing everything, diagnosing problem, fixing the problem, putting everything back. I would say allow 3-4 hours and pat yourself on the back if you do it quicker.
Note#2, if you have a large build up there is a hole in the floor of the freezer section. If the water does not evaporate it will run out of the hole and into your wooden floors! Place towels both inside and outside the unit just in case!
GE offered a "broken appliance" warranty for $379 for one year, with no guarantee that when a technician came to look at it, the repairs would be covered by the warranty!!! No thank you, you just want me to buy a new fridge. Okay, challenge on, I'll fix it myself.
I took everything from the back of the freezer out. Spent an hour defrosting (note: use hair dryer next time). Ruled out a motherboard problem (even though it appears I have the old style motherboard), removed dust build up from fan intake. I could not get the heater to come on, so I cut off the thermostat defroster and connected the wires together. The only way to get the heater on was to set the freezer control to 0 / zero.
So, ordered part from partselect.com and it arrived the next day!!!. Installed and unit appears to be defrosting okay after a week.
So now I'm back to order the ice maker part. The door flap will wait for another time.
Note: I've put in the time for novices and recognizing how the freezer is constructed.
Time includes taking everything out of the freezer section, unscrewing everything, diagnosing problem, fixing the problem, putting everything back. I would say allow 3-4 hours and pat yourself on the back if you do it quicker.
Note#2, if you have a large build up there is a hole in the floor of the freezer section. If the water does not evaporate it will run out of the hole and into your wooden floors! Place towels both inside and outside the unit just in case!
Was this instruction helpful to you?
Thank you for voting!