TBX25PRYARBB General Electric Refrigerator - Instructions

Removed two screws, lined up the rail and replaced the screws. That was it!! Glass shelf sat on top and bin slid in smoothly.

remove the 'pop-out " frame around the door recess, you pry the flexable seal from around the ice despenser, have someone hold the unit with the wiring, remove the one screw that holds the door recess, and replace the new one. reverse the procedure. remember to unplug thr frig. first

Your Video really made it easy, showing the actual replacment of the part. However I did have one problem, which was I could not unplug the panel just by pulling on the plugs. A locking catch is on each plug so I just moved the panel out of the way.

The solenoid in the dispenser was overheated due to the control board failure. After I rerplaced the board I found the heat had distorted the plastic crank and jammed the solenoid action. The plastic crank was easy to replace. Now after expending approx. $75 everything works normally!

Had to take front panel off dispenser area. Then remove components and install new part. That was easy part. Problem was getting components back into front of freezer. Seemed like something was blocking it from going all the way in. Had to remove small amount of insulation and "jiggle" components and eventually fell into place.

Replaced the complete Auger and Ice Bucket Assembly. The auger was not shaped on the end that fits into the slot in the icemaker exactly like the one it replaced, so I had to make a small adjustment in that end using a vise and pliers, otherwise it was very difficult to insert. It has helped but still requires some jiggleing to get it to slip in.

Since my refrig is 18 yrs. old and I never had to replace it, took a little long to remove trim piece on the outside. After that repair went smoothly. I still have problem with water collecting inside on the bottom of the freezer, might have a leak somewhere. Ice maker is functioning correctly.

Replaced flapper, which was in surprisingly good condition. Major part of repair was removing a lot of mold incurred from long term seepage of room air into the ice channel. In the process of the repair, I discovered that the solenoid to the right of the flapper was hanging up badly. I removed it and cleaned both the plunger and the interior cone of the solenoid with alcohol. This removed quite a bit of rust and some mold. Reinstalled solenoid, replaced flapper and it works just fine. May need to replace solenoid if problem recurs. Certainly worth $37.00!

Very Easy, follow direction I the video.

Repair went exactly like the video. With this video it was easy to make the repair. There were no surprises or problems and I felt confident in the videos instructions. It was like pushing the easy button.

Removed frame, unscrewed the electrical panel, and popped the flapper off. Installed new flapper. Replaced the electrical panel and re-installed the frame.

Removed control panel by inserting small screwdriver in the 3 holes underneath to loosen. Remove 4 screws holding circuit board . Unplugged 3 connectors. Removing circuit board gave access to flapper. Removed flapper by unclipping. Installed new flapper and reversed disassembly procedure. This was 2nd time in 2 years I had to replace this part.

Took out the vegetable bins, the glass and the shelf rack. Replaced the left side and the center glide. Worked easily.

I followed the video instructions (very helpful) and used others comments for removing the control panel. For the latter I used a small allen wrench to carefully wedge the bottom two indents (look from below panel edge) slightly up and forward to release the panel. Next, after removing the four screws, the assembly (housing shield) removed fairly easily. I then had full access to the flapper and removed this carefully with the pliers so as not to damage the piece it was attached to (Dispenser Door Recess Crank?). The rubber outer flange on the otherwise plastic flapper was very irregular for approx. 1/4 of the circumference and thus did not seal. So far it's been one week and no more frost build up or frozen water dispenser line.

The repair is somewhat self-explanatory. The old/broken rail which was broken needed to be unscrewed in front and rear, and the new one simply inserted and screwed in. Simple installation. What I REALLY wanted to share, is how impressed I was with the FAST service/speed that the parts arrived. Originally, we thought that just the middle drawer slide needed replacing, so I ordered the middle one and installed it. After installing it we realized that the right slide was broken too, so I ordered that. I placed the order on Saturday and the part was delivered to us on Tuesday!!! SUPURB service!! I will DEFINITELY order my next parts from PartSelect again!! Thanks for wonderful experience!