GTS22JBPDRWW General Electric Refrigerator - Instructions

Water still came out the front when pressed, but no ice. After removing the Ice container, & the top shelf I noted the icemake inlet was iced over. I turned off the icemaker, turned down the freezer temp, & allowed Ice to melt, but problem returned. I next removed the back bottom cover & cleaned the condenser coils, & drain pan; they were extremely dirty. Then I noticed the condensor fan was not on. After getting the nomenclature plate info off the condenser fan motor I left the back cover off, & put an external fan to blow on the coils as a temporaty fix until I could get the part & replace it. During that time the refrig functioned normally. 3 days later my condenser fan motor I ordered from Parts Select arrived & I installed it.

When the condensor fan motor started making those "Dying Mouse" noises I knew it was time to replace it. So I removed the fan motor and re-oiled it's lubricating packing, reinstalled it and promptly ordered a repacement moter online from PartSelect. I've ordered parts from them in the past with great results and rapid shipping. So now the "Dying Mouse" has been evicted and my wife is happy. And everyone should know, ( If Momma ain't happy, Then nobody's happy.) Thanks again PartSelect for your fast, reliable parts source with very reasonable prices.

Unplugged refrigerator and removed rear cover. Removed the two attaching cap screws from the mounting bracket. Removed fan blade by sliding it off the shaft, disconnected wiring plug and removed the motor. Removed the rubber grommets from the old motor and installed on the new unit. Set the new unit in place and reinstall the fan blade, mounting bracket and screw into place. Reconnect the wiring harness. To replace the relay, simply remove the wire clip from the relay cover, slide the relay off the connecting pins on the compressor and disconnect the wires. Slide the new relay into place, reconnect the wires and replace the cover.

Remove back panel . Removed fan shroud. Replaced fan and panel. Ops ck ok so far

took screw that holds motor frame in place out with nutdriver, rolled motor frame out after unplugging motor,took screw out of strap that held motor in frame, removed bushings from old motor and put them on the new one and re3versed the proceedure.

Follow the directions on the video, removed the back panel, unplugged the existing fan, removed the fan assembly, installed the new motor and reassembled the components.

On partselects video the gentleman removes the fan and housing in one piece. This is a great idea but does not work on this brand of ge. I removed the fan housing screw as instructed but left it in place and swiveled it enough to access the retaining screws with a socket driver. Over all swap of the fan was seamless and the video is a gem. Andy

took apart stat. area rplaced wire harness &t.stat simple but im a retired union electrican so wiring was a bit easy

Without the video, I would have been lost. I pulled the entire bracket out of the refrigerator, but could not insert the tab and adjust the bracket back in place, so I removed the bracket and motor, inserted the main frame bracket then re-installed the motor, fan , grommets, bracket. It's working.

I followed the instructions in the video regarding removal, repair and reinstall. It all went as the video said, except for the reinstall. The rear tab did not snick into place like the one in the video did, and it was extremely difficult to see whether or not it was inserted properly. I ended up inserting the rear tab by feel, and then I had to hold it in place while I stretched the front part of the frame to line up the screw hole in order to reinsert the screw. I had to have my wife hold the flashlight while I did that in order to see. Other than that, the repair went well, it is working like a charm, and I know I have a quality GE part in my refrigerator again! Many thanks to Partselect for their speediness in getting the part to me and giving me the needed information in getting the repair done! I will shop here again.

condenser fan on bottom condenser not runningchanged fan and fan motor

My compressor fan that blows over the coils was not spinning. I measured 120 VAC going to the fan so I knew it should have been spinning but wasn't. Took fan motor out and took it apart and super lubed the motor to get it spinning again temporarily until I could get the new one in. Put new one in and has been working for about 10 days now. Freezer is not below 0 deg F which is what you want. Frig is below 40 deg F also what you want.

unplug fridge! removed ice maker. removed the back panel in frezer. I uncliped thermostat; cut wires on thermostat and installed new thermostat.

Not knowing anything about a refrigerator it was hard to find the source of the noise. Once I could isolate it we googled the appliance repair and found the video from Parts Select and the rest was a piece of cake. Saved a service call and bloated parts prices. Thank you Parts Select!!!

pull out the slide pan lh and replace for the part