MSX22DLB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeff from Wooster, OH
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Door closing cam (made of Plastic) just wore out with age and broke in half
Took the door contents out and put them on the counter, took the door off the hinges by unscrewing the 2 screws on the top of the Fridge and lifting the door off the hinge onthe bottom. Then laid down the Fridge on the kitchen floor and replaced the Door Closing Cam, keeping in mind the order of the 3 shims and other things on the bottom of the door. Simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Danville, VA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
door dropped down and draging, would not close
Buy ( 2 ) cams !!!! removed hinge cover and hinge on top of the door, ( 2 screws )...lift door off of the bottom hinge and lay door on the floor, remove broken cam on bottom of door with nut driver, ( 2 screws ) , install new cam..... remove the bottom hinge off of the front of the refrigerator with nut driver, (2 screws ).... saw rivit off and remove old cam, install new cam and secure with new bolt and nut,... reinstall hinge back on bottom front of refigerator.....replace door back onto the bottom hinge.....install top hinge back onto the top of the door....replace hinge cover......done !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Natalie from Randallstown, MD
- Parts Used:
- WR17X2740
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
the auger was rusty, causing ice to have brown spots
Pay close attention to how you disassemble everything. You might even want to take a picture. I taped all the screws right where I unscrewed them, to make sure they were replaced in the right section. Also use the picture diagram that on the computer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Naples, FL
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Fridge door was not self-closing
Followed step-by-step instructions in previous post. Note that there are TWO approaches, both of which work.
Option 1) Order TWO cams (PS297995), drill out the rivet holding the frame's cam, and replace it with a nut and bolt. (See post on 07/19/09.)
Option 2) Order the entire hinge assembly (PS290199), which includes the door's cam and an assembled frame hinge and cam. (See post on 10/29/08.)
We opted for Option 1 which was pretty easy. Option 2 would be even easier and take less time but costs about $9 more.
Thanks to previous posters for excellent instructions!
Option 1) Order TWO cams (PS297995), drill out the rivet holding the frame's cam, and replace it with a nut and bolt. (See post on 07/19/09.)
Option 2) Order the entire hinge assembly (PS290199), which includes the door's cam and an assembled frame hinge and cam. (See post on 10/29/08.)
We opted for Option 1 which was pretty easy. Option 2 would be even easier and take less time but costs about $9 more.
Thanks to previous posters for excellent instructions!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- phyllis from owensville, MO
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Old Cam Had Deteriorated, And Was Breaking Into Pieces And Falling Off.
We taped the door with 3 pieces of duct tape, then put boards under it. Used socket set to remove cam and then cut off rivet so we could just use a screw to keep in place. . . Just for your information, I ordered 2 cams, and was glad I did as I need 2 to make the repair. . . Didn't read about this online or on order recommendation. The cams go 1 up and 1 down thanks for the installation repair stories, it inspired us to "do it ourselves " and we saved about $75 to $100. 00
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from New York, NY
- Parts Used:
- WR17X1407
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The light shield covering the bulb in the freezer cracked.
This was an extremely easy repair. The old light shield snapped out and the new one snapped in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Azle, TX
- Parts Used:
- WR17X2740
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
The auger was rusted with age and made the ice taste bad.
The disassembly and reassembly was straightforward but the parts diagram was very helpful to help you get it back together. Make sure you get the convexity of the clip that retains the clear plastic barrel to the auger pointing in the right direction. The metal plate that that comes out with the assembly seems to rust as fast as the auger, so you should just order that when you order the auger. I did not replace the plate so I cleaned it and painted it with epoxy paint before I reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from Boca Raton, FL
- Parts Used:
- WR72X209
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
slides were broken and draws cracked
Emptied the old draws and removed the old sliders. Took time to screw the new ones in. The draws are not as nice as the original ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Windham, NH
- Parts Used:
- WR17X2760
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
rust in the ice
there was rust inbedded in the ice cube. replaced the front plate in the ice maker bin. If you can't remember what parts you remover, take pictures of the replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jimmy from saluda, SC
- Parts Used:
- WR17X2740
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
would not dispence ice
remove ice bucket and replace broken augar
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Yakima, WA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
door was not closing properly
watched the video on changing the cam and then did the repair as per the instructions. the job was easy and now the door works as it should. that saved me lots of money by doing it myself. thanks, Martin.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PETE from LAKE FOREST PARK, WA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door would not close on first touch.
I ordered a door closing cam (4320595) to start with and then relized I needed Bottom Hinge Assembly which I ordered#4326874. I had no problem installing. I have returned for credit the door closing cam. I HAD NO TROUBLE INSTALLING THE BOTTOM HINGE ASSEMBLY. ONLY TOOK 10 OR 15 MINUTES. I am a retired building contactor and hade all the toos necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Flowood, MS
- Parts Used:
- WR71X10715
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed an extra shelf
Part was received quickly and quickly installed-Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Charlottesville, VA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The door closing cam disintegrated and had to lift door to close it
Ther was a video on how to repalce this part on your web site. Describing what tools were needed saved me running back and forth to my tool box. I followed the directions given in the video and repair was completed in 1/2 hour. That included meremoving then cleaning and replacing the sheves in the door. And by the way, the part was shipped the same day I ordered it and arrived on my doorstep noon the following day.
Was this instruction helpful to you?
Thank you for voting!