GTT16HBMFRWW General Electric Refrigerator - Instructions

Followed the video by Parts select. Very accurate to remove and replace. The only trouble I ran into was getting the clip back onto the fan blade shaft! Have to improvise and use a wirenut to spread it and it went right onto the shaft. Now working perfectly! Thanks for the video and the fast part service shipping...

I followed the instructions in the video. The decorative parts were slightly different than in the video, such as screws at the top versus the bottom, but all of the working parts were the same. I was somewhat hesitant about applying pressure to remove the locking spring and fan blades and to replace them but the video reassured me and all went well. The refrigerator is operating as quietly as when it was brand new.

The is my 'refreshment' cooler and sits in our garage. Hotter than heck in the summer so the things runs a lot. Started making a little growling noise. Had to partially disassemble the back panel to get to the fan. Touched the exposed shaft for a second and the sound stopped. OK, it's the fan. Went on line, used the (really great) exploded diagram to figure out what I needed. A couple days later the parts show up. Installed the new fan blade and retainer Removed the old motor (couple of mounting screws), connected the new motor (a plug in) and mounted the new motor making sure the grommet on the front and back were engaged. Turned the unit on and everything worked. Reinstalled the foam channel, the back panel and it ran perfectly. Great support (the diagram), fast delivery and fair pricing. Not bad!

I simply followed the online video instructions.made the job easy and fun.

I had already ordered a replacement evaporator motor from another vendor. I ordered the evaporator fan blade, compression ring and rubber grommets from PartSelect. Apparently this is a pretty common issue with top-freezer refrigerators. Obtaining these parts and possessing the few tools needed saved me at least $100 over having someone else perform the repair. I will further use PartSelect when ordering parts for my other appliances. Thank you.

unplug fridge! removed ice maker. removed the back panel in frezer. I uncliped thermostat; cut wires on thermostat and installed new thermostat.

Replaced above parts and the noise problem was not resolved. Ordered a new motor, fan blade and another set of grommets from PartSelect. The parts were delivered the next day. Took me about 15 minutes to swap the new parts in. It's been 3 days since the repair and the noise has not returned.

I replaced the noisy evaporator fan motor after watching the video provided. All went well and now I have a much quieter refrigerator. I took apart the old evaporator motor to see why it rattled when moved and it had an electrical part that came undone and was the cause of the obnoxious noise that came from the refrigerator. Now, my wife and I can sleep better now that the noisy fan was replaced.

First I looked at the video on changing out the fan.Made a lot of difference. Everything was covered and made it simple. Wish I had gotten two grommets but the back one was in good shape and worked fine. My hearing isn't great but now I can't even hear the thing run unless the freezer door is open. The shipping was great! You sent it out immediately and in a few days it was here.

Actually watch your video and it was really easy.

watch the video very good

The repair went smoothly and surpising easy! Get access to the back of the fridge. Unplug fridge, remove cardboard but save to put back in same place. For our fridge it was to bolts removed by socket set, removed old condenser fan motor (applyed a little pressure) and placed the new condenser fan motor in. It's easier with two sets of hands, but I've got to say DIRECTIONS OTHER THEN CUSTOMERS TESTIMONY SHOULD BE SENT WITH THE PART!! Otherwise quite simple.

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy

Simply removed the shelf from the refrigerator released the old reflector, which was cracked and brittle,and inserted the new reflector first to the shelf frame then to the glass shelf.

Once I found your site(GE wanted 2x the price for just the motor) I saw the video and the rest is history.Fantastic response with support and parts. Parts arrived when you said and the work was completed in under 15 min. Working GREAT!@!LS Haney